Buch
Spritzgießen von faserverstärkten Kunststoffen mit drehendem Werkzeugkern. Rheologie - praktische Untersuchungen - Auslegungsmethodik
Zusammenfassung
Beim Spritzgießen von länglichen rotationssymmetrischen Bauteilen führen Fertigungsrestriktionen sowie komplexe Geometrien oftmals dazu, dass die Bauteilfüllung in axialer Richtung erfolgt. Strömungsbedingt richten sich die Moleküle sowie ggf. vorhandene Verstärkungsfasern hierbei in Fließrichtung aus. Da bei faserverstärkten Kunststoffen die maximale Verstärkungswirkung erzielt wird, wenn ein Großteil der Fasern in Belastungsrichtung ausgerichtet ist, ist diese axiale Ausrichtung bei innendruckbelasteten Bauteilen nachteilig und führt zu einer ineffizienten Materialausnutzung. In dieser Arbeit wird gezeigt, wie bei solchen Bauteilen durch einen drehenden Werkzeugkern die Faserorientierung und die daraus resultierende Mechanik gezielt beeinflusst und für Innendruckbelastung optimiert werden kann. Um wichtige Einflussgrößen und deren Auswirkung bei dieser Prozesstechnologie zu charakterisieren, wird zu Beginn der Arbeit eine rheologische Vorbetrachtung vorgestellt. Diese zeigt u.a., dass sich die Einspritzgeschwindigkeit und die Rotationsgeschwindigkeit maßgeblich auf den resultierenden Schergeschwindigkeitsvektor auswirken und damit den größten Einfluss auf die Faserumorientierung haben. Die Berechnungen zeigen zudem,
dass die absolute Schergeschwindigkeit zwar maßgeblich von der Wanddicke und der Strukturviskosität der Polymerschmelze abhängen, diese Größen jedoch die Ausrichtung des resultierenden Schergeschwindigkeitsvektors nur geringfügig verändern. Im Anschluss folgen Kapitel, in denen die Prozessumsetzung des Spritzgießens mit drehendem Werkzeugkern sowie Methodiken zur direkten und indirekten Quantifizierung der Faserumorientierung vorgestellt werden. Darauf aufbauend werden umfangreiche Untersuchungen an kurz- und langfaserverstärktem Polypropylen und Polyamid u.a. zum Einfluss der Drehzahl, der Wanddicke, des Fasergehalts sowie von Spritzgießprozessparametern vorgestellt. Hierbei können die rheologischen Voruntersuchungen zum Teil bestätigt werden und es zeigt sich, dass unabhängig vom Material und der Wanddicke mit zunehmender Drehzahl ein Großteil der Fasern in tangentiale Richtung umorientiert werden kann. Mit steigender Drehzahl führt die rotationsinduzierte Scherung dazu, dass die ursprüngliche Schichtstruktur der Faserorientierung mit in Fließrichtung ausgerichteten Fasern in den Randschichten sowie quer zur Fließrichtung orientierten Fasern in der Kernschicht nicht mehr vorhanden
ist. Durch die Drehung werden die Randschichten schmaler und der Großteil der Fasern in diesen Schichten kann tangential ausgerichtet werden. Auch in der Kernschicht ist es möglich, die Fasern noch stärker auszurichten, wodurch beispielsweise der mittlere tangentiale Orientierungsgrad für ein kurzfaserverstärktes Polypropylen (PP-GF50) von 0,32 (ungedreht) auf 0,73 (gedreht mit 4,4 s-¹) erhöht werden kann. Kurzfassung Durch die vermehrt tangential ausgerichteten Fasern kann die Berstdruckfestigkeit signifikant, in vielen Versuchsreihen um über 100 %, gesteigert werden. Für ein kurzfaserverstärktes PP (PP-GF50) ist somit eine Steigerung von 58 bar auf 120 bar und für ein kurzfaserverstärktes Polyamid (PA-GF50) von 85 bar auf 159 bar möglich. Um den positiven Einfluss des drehenden Werkzeugkerns auf die Mechanik in der Simulation berücksichtigen zu können, folgt anschließend die Entwicklung einer Simulationsmethodik, mit der die beeinflusste Faserorientierung in der Struktursimulation abgebildet werden kann. Diese Simulationsmethodik kann an den Ergebnissen der Berstdruckprüfungen erfolgreich validiert werden. Darauf aufbauend wird eine Auslegungsmethodik für Bauteile, die mit einem drehenden Werkzeugkern hergestellt werden sollen, vorgestellt und auf zwei Bauteile aus der Industrie übertragen. Die Anwendung der Auslegungsmethodik bei diesen Bauteilen verdeutlicht zum Abschluss der Arbeit das große Potential der Prozesstechnologie: Bei einem innendruckbelasteten Bauteil mit einfacher Geometrie kann der Auslastungsgrad je nach Lastfall deutlich von u.a. 0,81 auf 0,47 reduziert werden. Bei einem Pumpengehäuse mit komplexer Geometrie kann durch die Rotation der Auslastungsgrad von 0,58 auf 0,4 gesenkt werden. Zudem führt die höhere Steifigkeit bei diesem Bauteil durch die in Belastungsrichtung ausgerichteten Fasern zu einer deutlich geringeren Verformung und der Reduktion von Spannungsspitzen.
dass die absolute Schergeschwindigkeit zwar maßgeblich von der Wanddicke und der Strukturviskosität der Polymerschmelze abhängen, diese Größen jedoch die Ausrichtung des resultierenden Schergeschwindigkeitsvektors nur geringfügig verändern. Im Anschluss folgen Kapitel, in denen die Prozessumsetzung des Spritzgießens mit drehendem Werkzeugkern sowie Methodiken zur direkten und indirekten Quantifizierung der Faserumorientierung vorgestellt werden. Darauf aufbauend werden umfangreiche Untersuchungen an kurz- und langfaserverstärktem Polypropylen und Polyamid u.a. zum Einfluss der Drehzahl, der Wanddicke, des Fasergehalts sowie von Spritzgießprozessparametern vorgestellt. Hierbei können die rheologischen Voruntersuchungen zum Teil bestätigt werden und es zeigt sich, dass unabhängig vom Material und der Wanddicke mit zunehmender Drehzahl ein Großteil der Fasern in tangentiale Richtung umorientiert werden kann. Mit steigender Drehzahl führt die rotationsinduzierte Scherung dazu, dass die ursprüngliche Schichtstruktur der Faserorientierung mit in Fließrichtung ausgerichteten Fasern in den Randschichten sowie quer zur Fließrichtung orientierten Fasern in der Kernschicht nicht mehr vorhanden
ist. Durch die Drehung werden die Randschichten schmaler und der Großteil der Fasern in diesen Schichten kann tangential ausgerichtet werden. Auch in der Kernschicht ist es möglich, die Fasern noch stärker auszurichten, wodurch beispielsweise der mittlere tangentiale Orientierungsgrad für ein kurzfaserverstärktes Polypropylen (PP-GF50) von 0,32 (ungedreht) auf 0,73 (gedreht mit 4,4 s-¹) erhöht werden kann. Kurzfassung Durch die vermehrt tangential ausgerichteten Fasern kann die Berstdruckfestigkeit signifikant, in vielen Versuchsreihen um über 100 %, gesteigert werden. Für ein kurzfaserverstärktes PP (PP-GF50) ist somit eine Steigerung von 58 bar auf 120 bar und für ein kurzfaserverstärktes Polyamid (PA-GF50) von 85 bar auf 159 bar möglich. Um den positiven Einfluss des drehenden Werkzeugkerns auf die Mechanik in der Simulation berücksichtigen zu können, folgt anschließend die Entwicklung einer Simulationsmethodik, mit der die beeinflusste Faserorientierung in der Struktursimulation abgebildet werden kann. Diese Simulationsmethodik kann an den Ergebnissen der Berstdruckprüfungen erfolgreich validiert werden. Darauf aufbauend wird eine Auslegungsmethodik für Bauteile, die mit einem drehenden Werkzeugkern hergestellt werden sollen, vorgestellt und auf zwei Bauteile aus der Industrie übertragen. Die Anwendung der Auslegungsmethodik bei diesen Bauteilen verdeutlicht zum Abschluss der Arbeit das große Potential der Prozesstechnologie: Bei einem innendruckbelasteten Bauteil mit einfacher Geometrie kann der Auslastungsgrad je nach Lastfall deutlich von u.a. 0,81 auf 0,47 reduziert werden. Bei einem Pumpengehäuse mit komplexer Geometrie kann durch die Rotation der Auslastungsgrad von 0,58 auf 0,4 gesenkt werden. Zudem führt die höhere Steifigkeit bei diesem Bauteil durch die in Belastungsrichtung ausgerichteten Fasern zu einer deutlich geringeren Verformung und der Reduktion von Spannungsspitzen.
In the injection moulding of elongated, rotationally symmetrical components, manufacturing
restrictions and complex geometries often result in the component being filled in the
axial direction. As a result of this flow, the molecules and possible reinforcement fibres
are aligned in the direction of flow. Since the maximum strengthening effect is achieved
with fibre-reinforced plastics when the majority of the fibres are aligned in the direction
of the load, this axial alignment is disadvantageous for components exposed to internal
pressure and leads to inefficient material utilization. In this work, it is shown how the fibre
orientation and the resulting mechanics can be intentionally influenced and optimized for
internal pressure loading in such structural parts by using a rotating mould core.
In order to characterise important influencing variables and their effect in this process
technology, a preliminary rheological analysis is presented at the beginning of this thesis.
The rheological analysis shows, among other things, that the injection speed and the
rotation speed have a significant effect on the resulting shear velocity vector and thus
have the greatest influence on the fibre reorientation. The analyses also show that the
absolute shear rate depends significantly on the wall thickness and the structural viscosity
of the polymer melt, but that these parameters only slightly change the orientation of the
resulting shear rate vector. Afterwards, chapters are presented in which the process implementation of injection moulding with a rotating mould core as well as methods for the direct and indirect quantification of the fibre reorientation are presented.
Based on this, comprehensive investigations of short and long fibre-reinforced polypropylene and polyamide are presented, including the influence of speed, wall thickness, fibre content and injection moulding process parameters. The preliminary rheological analysis can be partially confirmed and it is shown that, regardless of the material and the wall thickness, the majority of the fibres can be reoriented in the tangential direction with increasing rotational speed. By increasing the rotational speed, the rotation-induced shear has the effect that the originally layered structure of the fibre orientation with fibres oriented in the flow direction in the outer layers and fibres oriented transversely to the flow direction in the core layer is no longer present. Due to the rotation, the outer layers become narrower and the majority of the fibres in these layers can be oriented tangentially. It is also possible to further align the fibres in the core layer, whereby, for example, the average degree of tangential orientation for a short-fibre reinforced polypropylene (PP-GF50) can be increased from 0,32 (unrotated) to 0,73 (rotated with 4,4 s-¹). Through the increased tangentially oriented fibres, the bursting strength can be significantly increased, in many test series by more than 100 %. Consequently, for a short-fibre x Abstract reinforced PP (PP-GF50) an increase from 58 bar to 120 bar and for a short-fibre reinforced polyamide (PA-GF50) from 85 bar to 159 bar is achieved.
In order to be able to consider the positive effect of the rotating mould core on the mechanics in the simulation, a methodology is developed with which the influenced fibre
orientation can be taken into account in the structural simulation. This simulation methodology is validated on the results of the bursting pressure tests.
Based on this, a design methodology for components that are to be manufactured with a
rotating mould core is presented and applied to two structural components from industry.
The application of the design methodology to these components demonstrates the significant potential of the process technology at the end of this thesis: For a component with simple geometry that is subjected to internal pressure, the load factor can be significantly reduced from 0,81 to 0,47 depending on the load case. For a pump casing with complex geometry, the rotation can reduce the load factor from 0,58 to 0,4. In addition, the higher stiffness in this component due to the fibres aligned in the direction of the load leads to significantly lower deformation and the reduction of stress
restrictions and complex geometries often result in the component being filled in the
axial direction. As a result of this flow, the molecules and possible reinforcement fibres
are aligned in the direction of flow. Since the maximum strengthening effect is achieved
with fibre-reinforced plastics when the majority of the fibres are aligned in the direction
of the load, this axial alignment is disadvantageous for components exposed to internal
pressure and leads to inefficient material utilization. In this work, it is shown how the fibre
orientation and the resulting mechanics can be intentionally influenced and optimized for
internal pressure loading in such structural parts by using a rotating mould core.
In order to characterise important influencing variables and their effect in this process
technology, a preliminary rheological analysis is presented at the beginning of this thesis.
The rheological analysis shows, among other things, that the injection speed and the
rotation speed have a significant effect on the resulting shear velocity vector and thus
have the greatest influence on the fibre reorientation. The analyses also show that the
absolute shear rate depends significantly on the wall thickness and the structural viscosity
of the polymer melt, but that these parameters only slightly change the orientation of the
resulting shear rate vector. Afterwards, chapters are presented in which the process implementation of injection moulding with a rotating mould core as well as methods for the direct and indirect quantification of the fibre reorientation are presented.
Based on this, comprehensive investigations of short and long fibre-reinforced polypropylene and polyamide are presented, including the influence of speed, wall thickness, fibre content and injection moulding process parameters. The preliminary rheological analysis can be partially confirmed and it is shown that, regardless of the material and the wall thickness, the majority of the fibres can be reoriented in the tangential direction with increasing rotational speed. By increasing the rotational speed, the rotation-induced shear has the effect that the originally layered structure of the fibre orientation with fibres oriented in the flow direction in the outer layers and fibres oriented transversely to the flow direction in the core layer is no longer present. Due to the rotation, the outer layers become narrower and the majority of the fibres in these layers can be oriented tangentially. It is also possible to further align the fibres in the core layer, whereby, for example, the average degree of tangential orientation for a short-fibre reinforced polypropylene (PP-GF50) can be increased from 0,32 (unrotated) to 0,73 (rotated with 4,4 s-¹). Through the increased tangentially oriented fibres, the bursting strength can be significantly increased, in many test series by more than 100 %. Consequently, for a short-fibre x Abstract reinforced PP (PP-GF50) an increase from 58 bar to 120 bar and for a short-fibre reinforced polyamide (PA-GF50) from 85 bar to 159 bar is achieved.
In order to be able to consider the positive effect of the rotating mould core on the mechanics in the simulation, a methodology is developed with which the influenced fibre
orientation can be taken into account in the structural simulation. This simulation methodology is validated on the results of the bursting pressure tests.
Based on this, a design methodology for components that are to be manufactured with a
rotating mould core is presented and applied to two structural components from industry.
The application of the design methodology to these components demonstrates the significant potential of the process technology at the end of this thesis: For a component with simple geometry that is subjected to internal pressure, the load factor can be significantly reduced from 0,81 to 0,47 depending on the load case. For a pump casing with complex geometry, the rotation can reduce the load factor from 0,58 to 0,4. In addition, the higher stiffness in this component due to the fibres aligned in the direction of the load leads to significantly lower deformation and the reduction of stress
Zusätzliche Informationen
Zugleich: Dissertation, Universität Kassel, 2023Druckausgabe
Link zu kassel university pressZitieren
@book{doi:10.17170/kobra-202401159367,
author={Land, Philipp},
title={Spritzgießen von faserverstärkten Kunststoffen mit drehendem Werkzeugkern. Rheologie - praktische Untersuchungen - Auslegungsmethodik},
publisher={kassel university press},
year={2024}
}
0500 Oax 0501 Text $btxt$2rdacontent 0502 Computermedien $bc$2rdacarrier 1100 2024$n2024 1500 1/ger 2050 ##0##http://hdl.handle.net/123456789/15487 3000 Land, Philipp 4000 Spritzgießen von faserverstärkten Kunststoffen mit drehendem Werkzeugkern. Rheologie - praktische Untersuchungen - Auslegungsmethodik / Land, Philipp 4030 4060 Online-Ressource 4085 ##0##=u http://nbn-resolving.de/http://hdl.handle.net/123456789/15487=x R 4204 \$dBuch 4170 5550 {{Spritzgießen}} 5550 {{Simulation}} 5550 {{Kunststoff}} 5550 {{Rheologie}} 7136 ##0##http://hdl.handle.net/123456789/15487
2024-02-23T16:20:21Z 2024-02-23T16:20:21Z 2024 doi:10.17170/kobra-202401159367 http://hdl.handle.net/123456789/15487 Zugleich: Dissertation, Universität Kassel, 2023 ger kassel university press Namensnennung - Weitergabe unter gleichen Bedingungen 4.0 International http://creativecommons.org/licenses/by-sa/4.0/ Werkzeugsystem mit drehendem Kern faserverstärkte Kunststoffe Faserorientierung Spritzgieß-Sonderverfahren Simulation 600 Spritzgießen von faserverstärkten Kunststoffen mit drehendem Werkzeugkern. Rheologie - praktische Untersuchungen - Auslegungsmethodik Buch Beim Spritzgießen von länglichen rotationssymmetrischen Bauteilen führen Fertigungsrestriktionen sowie komplexe Geometrien oftmals dazu, dass die Bauteilfüllung in axialer Richtung erfolgt. Strömungsbedingt richten sich die Moleküle sowie ggf. vorhandene Verstärkungsfasern hierbei in Fließrichtung aus. Da bei faserverstärkten Kunststoffen die maximale Verstärkungswirkung erzielt wird, wenn ein Großteil der Fasern in Belastungsrichtung ausgerichtet ist, ist diese axiale Ausrichtung bei innendruckbelasteten Bauteilen nachteilig und führt zu einer ineffizienten Materialausnutzung. In dieser Arbeit wird gezeigt, wie bei solchen Bauteilen durch einen drehenden Werkzeugkern die Faserorientierung und die daraus resultierende Mechanik gezielt beeinflusst und für Innendruckbelastung optimiert werden kann. Um wichtige Einflussgrößen und deren Auswirkung bei dieser Prozesstechnologie zu charakterisieren, wird zu Beginn der Arbeit eine rheologische Vorbetrachtung vorgestellt. Diese zeigt u.a., dass sich die Einspritzgeschwindigkeit und die Rotationsgeschwindigkeit maßgeblich auf den resultierenden Schergeschwindigkeitsvektor auswirken und damit den größten Einfluss auf die Faserumorientierung haben. Die Berechnungen zeigen zudem, dass die absolute Schergeschwindigkeit zwar maßgeblich von der Wanddicke und der Strukturviskosität der Polymerschmelze abhängen, diese Größen jedoch die Ausrichtung des resultierenden Schergeschwindigkeitsvektors nur geringfügig verändern. Im Anschluss folgen Kapitel, in denen die Prozessumsetzung des Spritzgießens mit drehendem Werkzeugkern sowie Methodiken zur direkten und indirekten Quantifizierung der Faserumorientierung vorgestellt werden. Darauf aufbauend werden umfangreiche Untersuchungen an kurz- und langfaserverstärktem Polypropylen und Polyamid u.a. zum Einfluss der Drehzahl, der Wanddicke, des Fasergehalts sowie von Spritzgießprozessparametern vorgestellt. Hierbei können die rheologischen Voruntersuchungen zum Teil bestätigt werden und es zeigt sich, dass unabhängig vom Material und der Wanddicke mit zunehmender Drehzahl ein Großteil der Fasern in tangentiale Richtung umorientiert werden kann. Mit steigender Drehzahl führt die rotationsinduzierte Scherung dazu, dass die ursprüngliche Schichtstruktur der Faserorientierung mit in Fließrichtung ausgerichteten Fasern in den Randschichten sowie quer zur Fließrichtung orientierten Fasern in der Kernschicht nicht mehr vorhanden ist. Durch die Drehung werden die Randschichten schmaler und der Großteil der Fasern in diesen Schichten kann tangential ausgerichtet werden. Auch in der Kernschicht ist es möglich, die Fasern noch stärker auszurichten, wodurch beispielsweise der mittlere tangentiale Orientierungsgrad für ein kurzfaserverstärktes Polypropylen (PP-GF50) von 0,32 (ungedreht) auf 0,73 (gedreht mit 4,4 s-¹) erhöht werden kann. Kurzfassung Durch die vermehrt tangential ausgerichteten Fasern kann die Berstdruckfestigkeit signifikant, in vielen Versuchsreihen um über 100 %, gesteigert werden. Für ein kurzfaserverstärktes PP (PP-GF50) ist somit eine Steigerung von 58 bar auf 120 bar und für ein kurzfaserverstärktes Polyamid (PA-GF50) von 85 bar auf 159 bar möglich. Um den positiven Einfluss des drehenden Werkzeugkerns auf die Mechanik in der Simulation berücksichtigen zu können, folgt anschließend die Entwicklung einer Simulationsmethodik, mit der die beeinflusste Faserorientierung in der Struktursimulation abgebildet werden kann. Diese Simulationsmethodik kann an den Ergebnissen der Berstdruckprüfungen erfolgreich validiert werden. Darauf aufbauend wird eine Auslegungsmethodik für Bauteile, die mit einem drehenden Werkzeugkern hergestellt werden sollen, vorgestellt und auf zwei Bauteile aus der Industrie übertragen. Die Anwendung der Auslegungsmethodik bei diesen Bauteilen verdeutlicht zum Abschluss der Arbeit das große Potential der Prozesstechnologie: Bei einem innendruckbelasteten Bauteil mit einfacher Geometrie kann der Auslastungsgrad je nach Lastfall deutlich von u.a. 0,81 auf 0,47 reduziert werden. Bei einem Pumpengehäuse mit komplexer Geometrie kann durch die Rotation der Auslastungsgrad von 0,58 auf 0,4 gesenkt werden. Zudem führt die höhere Steifigkeit bei diesem Bauteil durch die in Belastungsrichtung ausgerichteten Fasern zu einer deutlich geringeren Verformung und der Reduktion von Spannungsspitzen. In the injection moulding of elongated, rotationally symmetrical components, manufacturing restrictions and complex geometries often result in the component being filled in the axial direction. As a result of this flow, the molecules and possible reinforcement fibres are aligned in the direction of flow. Since the maximum strengthening effect is achieved with fibre-reinforced plastics when the majority of the fibres are aligned in the direction of the load, this axial alignment is disadvantageous for components exposed to internal pressure and leads to inefficient material utilization. In this work, it is shown how the fibre orientation and the resulting mechanics can be intentionally influenced and optimized for internal pressure loading in such structural parts by using a rotating mould core. In order to characterise important influencing variables and their effect in this process technology, a preliminary rheological analysis is presented at the beginning of this thesis. The rheological analysis shows, among other things, that the injection speed and the rotation speed have a significant effect on the resulting shear velocity vector and thus have the greatest influence on the fibre reorientation. The analyses also show that the absolute shear rate depends significantly on the wall thickness and the structural viscosity of the polymer melt, but that these parameters only slightly change the orientation of the resulting shear rate vector. Afterwards, chapters are presented in which the process implementation of injection moulding with a rotating mould core as well as methods for the direct and indirect quantification of the fibre reorientation are presented. Based on this, comprehensive investigations of short and long fibre-reinforced polypropylene and polyamide are presented, including the influence of speed, wall thickness, fibre content and injection moulding process parameters. The preliminary rheological analysis can be partially confirmed and it is shown that, regardless of the material and the wall thickness, the majority of the fibres can be reoriented in the tangential direction with increasing rotational speed. By increasing the rotational speed, the rotation-induced shear has the effect that the originally layered structure of the fibre orientation with fibres oriented in the flow direction in the outer layers and fibres oriented transversely to the flow direction in the core layer is no longer present. Due to the rotation, the outer layers become narrower and the majority of the fibres in these layers can be oriented tangentially. It is also possible to further align the fibres in the core layer, whereby, for example, the average degree of tangential orientation for a short-fibre reinforced polypropylene (PP-GF50) can be increased from 0,32 (unrotated) to 0,73 (rotated with 4,4 s-¹). Through the increased tangentially oriented fibres, the bursting strength can be significantly increased, in many test series by more than 100 %. Consequently, for a short-fibre x Abstract reinforced PP (PP-GF50) an increase from 58 bar to 120 bar and for a short-fibre reinforced polyamide (PA-GF50) from 85 bar to 159 bar is achieved. In order to be able to consider the positive effect of the rotating mould core on the mechanics in the simulation, a methodology is developed with which the influenced fibre orientation can be taken into account in the structural simulation. This simulation methodology is validated on the results of the bursting pressure tests. Based on this, a design methodology for components that are to be manufactured with a rotating mould core is presented and applied to two structural components from industry. The application of the design methodology to these components demonstrates the significant potential of the process technology at the end of this thesis: For a component with simple geometry that is subjected to internal pressure, the load factor can be significantly reduced from 0,81 to 0,47 depending on the load case. For a pump casing with complex geometry, the rotation can reduce the load factor from 0,58 to 0,4. In addition, the higher stiffness in this component due to the fibres aligned in the direction of the load leads to significantly lower deformation and the reduction of stress open access Land, Philipp 2023-12-04 xiii, 198 Seiten Kassel, Universität Kassel, Fachbereich Maschinenbau Heim, Hans-Peter (Prof. Dr.-Ing.) Krumpholz, Thorsten (Prof. Dr.-Ing.) Kassel 978-3-7376-1160-2 Spritzgießen Simulation Kunststoff Rheologie publishedVersion Schriftenreihe des Instituts für Werkstofftechnik / Kunststofftechnik Band 18 true 39,00 Schriftenreihe des Instituts für Werkstofftechnik / Kunststofftechnik Naturwissenschaft, Technik, Informatik, Medizin Dissertation FB 15 / Maschinenbau Softcover DIN A5 true
Die folgenden Lizenzbestimmungen sind mit dieser Ressource verbunden: