Suche
Anzeige der Dokumente 21-30 von 40
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Damage Tolerance Evaluation of E-PBF-Manufactured Inconel 718 Strut Geometries by Advanced Characterization Techniques
(2020-01-06)
By means of electron beam powder bed fusion (E-PBF), highly complex lightweight structures can be manufactured within short process times. Due to the increasing complexity of producible components and the entangled interplay of damage mechanisms, common bulk material properties such as ultimate tensile or fatigue strength are not sufficient to guarantee safe and reliable use in demanding applications. Within this work, the damage tolerance of E-PBF-manufactured Ni-based alloy Inconel 718 (IN 718) strut geometries ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Tribological Performance of Additively Manufactured AISI H13 Steel in Different Surface Conditions
(2021-02-16)
Additive manufacturing of metallic tribological components offers unprecedented degrees of freedom, but the surface roughness of most as-printed surfaces impedes the direct applicability of such structures, and postprocessing is necessary. Here, the tribological performance of AISI H13 steel samples was studied. These were additively manufactured through laser powder bed fusion (L-PBF), also referred to as selective laser melting (SLM). Samples were tested in four different surface conditions: as-printed, polished, ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Elevated Temperature Mechanical Characteristics and Fracture Behavior of a Novel Beta Titanium Alloy
(2023-02-03)
In the present work, the elevated-temperature deformation characteristics and microstructural evolution of a Ti-5V-5Mo-5Cr-4Al alloy in solution-treatment conditions were studied under a tensile load at temperatures in the range of 25 to 550 °C and strain rates between 0.001 and 0.1 s-¹. The results obtained indicated that, essentially, dynamic recovery (DRV) was the dominant softening mechanism in the case of the regimes considered. An analysis based on transmission electron microscopy (TEM) and the assessment of ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Overmoulding of Additively Manufactured Titanium Inserts Using Polyoxymethylene (POM)—Evaluation of Bond Quality as a Function of Process Parameters
(2021-06-15)
Due to their process-induced porous surfaces, additively manufactured structures are not optimized for applications in which friction is a key factor. To improve the frictional properties of additively manufactured titanium inserts of various thicknesses, two tribologically optimized POM materials, which differ in terms of filler composition and contents, were used to overmould the inserts. The titanium inserts were manufactured in two different building directions, resulting in a variation in surface roughness. The ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Microstructural Constituents and Mechanical Properties of Low-Density Fe-Cr-Ni-Mn-Al-C Stainless Steels
(2022-07-23)
Metallic material concepts associated with the sustainable and efficient use of resources are currently the subject of intensive research. Al addition to steel offers advantages in view of lightweight, durability, and efficient use of high-Fe scrap from the Al industry. In the present work, Al was added to Fe-12Cr-(9,12)Ni-3Mn-0.3C-xAl (x = 0.1–6) (wt.%) stainless steels to assess its influence on microstructure and mechanical properties. According to density measurements based on Archimedes’ principle, densities ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Determination and Validation of Residual Stresses in CFRP/Metal Hybrid Components Using the Incremental Hole Drilling Method
(2020-09-21)
Lightweight materials contribute to an efficient decrease in fuel consumption in the automotive and aircraft industries. Hybrid components made of metal and carbon fiber-reinforced plastics (CFRP) have a high potential in lightweight applications due to their high strength-to-weight ratio. For cost-effective processing of hybrid materials, advanced manufacturing processes such as the prepreg-press-technology have been developed, in which the bonding between a metallic component and a fiber compound is exclusively ...
Aufsatz
Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
(2022-03-08)
This publication investigates the adhesion between an injection molded component and a self-reinforced composite (SRC) produced in a combined compaction and back-injection process to produce back-injected self-reinforced composites. To study the influence of the process, the parameters barrel temperature, time of injection, and tool temperature were varied. In addition, samples were taken at different positions along the flow path. In light of the orthotropic material behavior of SRCs, investigations were conducted ...
Aufsatz
Holzdesign trifft Kunststofftechnik
(2022)
Werkstoffverbunde aus Holzgeweben in einer thermoplastischen Matrix verbinden die Idee des textilen Holzbaus mit der Faserverbundtechnologie. In einem Projekt werden Fassadenelemente aus solchen Wood Textile Composites hergestellt. Dabei spielt neben den mechanischen Anforderungen auch die gestalterische Seite und die Akzeptanz der zukünftigen Nutzer eine wichtige Rolle.
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Influence of Microstructure and Defects on Mechanical Properties of AISI H13 Manufactured by Electron Beam Powder Bed Fusion
(2021-08-04)
Electron beam powder bed fusion (E-PBF) is a well-known additive manufacturing process. Components are realized based on layer-by-layer melting of metal powder. Due to the high degree of design freedom, additive manufacturing came into focus of tooling industry, especially for tools with sophisticated internal cooling channels. The present work focuses on the relationships between processing, microstructure evolution, chemical composition and mechanical properties of a high alloyed tool steel AISI H13 (1.2344, ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Hot Work Tool Steel Processed by Laser Powder Bed Fusion: A Review on Most Relevant Influencing Factors
(2021-03-26)
As a representative of a common carbon-bearing hot work tool steel AISI H13 is in focus of the present review paper. Most relevant details for processing of AISI H13 by laser powder bed fusion (L-PBF) are systematically investigated. Three common stages of process parameter development and material assessment, respectively, are in focus: general processibility, process refinement, and deduction of process–microstructure–property relations, i.e., understanding of the interplay of relevant elementary mechanisms. On the ...