Suche
Anzeige der Dokumente 31-40 von 101
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
A Novel Thermo-Mechanical Processing Route Exploiting Abnormal Grain Growth in Heusler-Type Co–Ni–Ga Shape Memory Alloys
(2022-10-04)
Heusler-type Co–Ni–Ga shape memory alloys attracted significant scientific attention owing to excellent superelasticity in single-crystalline state. However, due to pronounced anisotropy, polycrystalline Co–Ni–Ga suffers from transformation-induced constraints at grain boundaries and, thus, premature failure upon thermo-mechanical loading. The present study reports on a novel thermo-mechanical processing route. Hot rolling followed by solution-annealing promotes abnormal grain growth, eventually leading to high-performance ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Cooling rate as a process parameter in advanced roll forming to tailor microstructure,mechanical and corrosion properties of EN AW 7075 tubes
(2022-12-14)
The effects of solution heat treatment parameters and quench media as a processing tool for tailoring microstructure, mechanical and corrosion properties in roll forming of EN AW 7075 alloy were studied. The highest yield stress and ultimate tensile strength were obtained for the specimens quenched in water, while the air-cooled specimens exhibited inferior mechanical properties. Microstructural analysis of specimens showed that except water-quenched specimens, the parts cooled/quenched in oil, in direct contact with ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
On the low-cycle fatigue behavior of thermo-mechanically processed high-strength aluminum alloys
(2021)
In the present work low-cycle fatigue experiments were carried out on thermo-mechanically processed AA6082 and AA7075 sheets to evaluate mechanical properties under cyclic loading. Different cooling rates imposed by use of tempered forming tools after solutionizing and subsequent aging treatment led to the formation of precipitates with differing sizes and morphologies. Specimens thermo-mechanically processed in tools with temperatures of 24 °C and 200 °C showed superior mechanical properties under both monotonic and ...
Aufsatz
On the Friction Stir Processing of Additive-Manufactured 316L Stainless Steel
(2022)
The novel combination of friction stir processing (FSP) and additive manufacturing (AM) is studied herein. Laser-based powder bed fusion of metals (PBF-LB/M) is used to establish 316 L stainless steel with a bimodal microstructure. Upon FSP, the as-built bimodal microstructure with an average grain size of 179 μm is transformed into the unimodal microstructure containing ultrafine grains with an average grain size of 1.2 μm. Results obtained by mechanical testing reveal that after FSP; the hardness, the yield point, ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Influence of deep rolling at different temperatures on near-surface and mechanical properties of a Maraging C250 steel
(2024-04-27)
Due to an outstanding combination of high strength and fracture toughness Maraging steels are used in numerous industries, e.g., in the aerospace sector. The high strength can be attributed to precipitation strengthening by conventional age-hardening heat treatments. However, as many of the envisaged applications will suffer from cyclic loadings, the fatigue properties are of significant interest in terms of a reliable use. Generally, Maraging steels are characterized by a relatively low fatigue strength limiting the ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Oxide Modified Iron in Electron Beam Powder Bed Fusion - From Processability to Corrosion Properties
(2022-03-07)
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material composition, and the solidification behavior of the material considered. However, when complex specific requirements have to be met, a targeted part design is highly challenging. In the field of biodegradable implant surgery, a cytocompatible material of an application-adapted ...
Konferenzveröffentlichung
On the Challenges toward Realization of Functionally Graded Structures by Electron Beam Melting—Fe-Base Shape Memory Alloy and Stainless Steel
(ASTM International, 2020-09-22)
In the present study, an iron-manganese-aluminum-nickel (Fe-Mn-Al-Ni) shape memory alloy was processed on an austenitic steel (AISI 304) build platform by electron beam melting in order to study the feasibility of realizing functionally graded structures consisting of two different materials (i.e., a functional and a structural material). Compression specimens consisting of the processed shape memory alloy and the austenitic build platform in equal parts were investigated. The microstructure was analyzed in the ...
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
Process Influences in the Combined Compacting and Back-Injection Process to Produce Back-Injected Self-Reinforced Composites (SRCs) – Analysis via Multiple Regression Modelling
(2021-11-21)
A new process to produce back-injected self-reinforced composites (SRCs) is presented. In contrast to other investigations on back-injection of SRCs, a process is presented which allows compacting and back injection of SRCs in one step where the SRCs are partly consolidated only via melt pressure inside the cavity. The mechanical properties of SRCs depend to a large extent on the process parameters of temperature and pressure during manufacture. These parameters are not yet known for back-injected areas. Sensors ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Mechanical Characterization and Simulation of Wood Textile Composites (WTC) supported by Digital Image Correlation (DIC)
(2023-05-30)
Wood Textile Composites (WTC) based on willow wood fabrics and polypropylene were produced using a hot compacting process in order to open up new and innovative areas of applications for wood. Due to their attractive and variable design, the WTCs are to be used in areas with a high visual impact, for example as a facade element. In tensile and 3-point bending tests, it was shown that the mechanical properties of WTC are strongly dependent on the heterogeneous structure of the composite. Both strength and elongation ...