Suche
Anzeige der Dokumente 11-18 von 18
Aufsatz
On the structural integrity of Fe-36Ni Invar alloy processed by selective laser melting
(2020)
Specimens made from pre-alloyed Invar (Fe-36Ni) powder were fabricated by selective laser melting and stress-relief heat treated afterwards. A relative density of the fabricated parts of 99.6 % was determined by computed tomography. The microstructure and mechanical behavior under monotonic and particularly cyclic loading at ambient temperature were investigated. Results reveal a bimodal microstructure containing columnar and equiaxed grains with an average grain size of 75 μm and pronounced texture 〈001〉 || BD. The ...
Aufsatz
Dynamic Tensile Deformation of High Strength Aluminum Alloys Processed Following Novel Thermomechanical Treatment Strategies
(2020-05-14)
Herein, the effects of a very recently introduced novel thermomechanical process route on the microstructural evolution and dynamic tensile deformation behavior of two different precipitation hardenable aluminum alloys, i.e., AA6082 and AA7075, are studied. The investigated materials are hot formed and quenched in differently tempered tools to reveal the influence of cooling rate. Microstructure analysis is conducted to study the influences of different cooling strategies on the microstructure evolution and prevailing ...
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
Characterization of Mechanical Properties, Macroscopic Deformation Behavior, and Microstructure of Functionally Graded 22MnB5 Steel
(2021-03-24)
The focus of this study is on the characterization of the local plastic deformation and failure of functionally graded 22MnB5 plates after hot stamping using an in situ approach. Various forming strategies at elevated temperatures are performed using differentially tempered forming tools to locally tailor the microstructure. By controlling the cooling rate, graded as well as martensitic and ferritic–pearlitic microstructures are obtained. Experimental analysis includes evaluation of the material- and geometry-dependent ...
Aufsatz
On the Influence of Microstructure on the Corrosion Behavior of Fe–Mn–Al–Ni Shape Memory Alloy in 5.0 wt% NaCl Solution
(2020-10-03)
Herein the corrosion behavior of Fe–Mn–Al–Ni shape memory alloys characterized by different microstructures in a 5.0 wt% NaCl solution is investigated. Open circuit potential and potentiodynamic polarisation tests are conducted. Generally, Fe–Mn–Al–Ni shows corrosion properties being similar to pure iron. However, the polarization curves of single crystals indicate the presence of an unstable passive system. The corrosion damage is analyzed by means of optical microscopy and electron microscopy. It is revealed that ...
Aufsatz
On the low-cycle fatigue behavior of thermo-mechanically processed high-strength aluminum alloys
(2021)
In the present work low-cycle fatigue experiments were carried out on thermo-mechanically processed AA6082 and AA7075 sheets to evaluate mechanical properties under cyclic loading. Different cooling rates imposed by use of tempered forming tools after solutionizing and subsequent aging treatment led to the formation of precipitates with differing sizes and morphologies. Specimens thermo-mechanically processed in tools with temperatures of 24 °C and 200 °C showed superior mechanical properties under both monotonic and ...
Aufsatz
Investigation of residual stresses in polypropylene using hot plate welding
(2020-08-05)
During the cooling process of the molten material, residual stresses appear because the reduced volume of the cooled material cannot fully fill the space formerly occupied by the molten material. The morphology in and around the weld is formed by different factors depending on the material and process parameters. Different morphological structures relate to different mechanical properties. The process parameters and the welding results including morphology and residual stress are linked together. In this article, ...
Aufsatz
Process Influences in the Combined Compacting and Back-Injection Process to Produce Back-Injected Self-Reinforced Composites (SRCs) – Analysis via Multiple Regression Modelling
(2021-11-21)
A new process to produce back-injected self-reinforced composites (SRCs) is presented. In contrast to other investigations on back-injection of SRCs, a process is presented which allows compacting and back injection of SRCs in one step where the SRCs are partly consolidated only via melt pressure inside the cavity. The mechanical properties of SRCs depend to a large extent on the process parameters of temperature and pressure during manufacture. These parameters are not yet known for back-injected areas. Sensors ...