Search
Now showing items 21-30 of 77
Aufsatz
Oxide Modified Iron in Electron Beam Powder Bed Fusion - From Processability to Corrosion Properties
(2022-03-07)
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material composition, and the solidification behavior of the material considered. However, when complex specific requirements have to be met, a targeted part design is highly challenging. In the field of biodegradable implant surgery, a cytocompatible material of an application-adapted ...
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
Process Influences in the Combined Compacting and Back-Injection Process to Produce Back-Injected Self-Reinforced Composites (SRCs) – Analysis via Multiple Regression Modelling
(2021-11-21)
A new process to produce back-injected self-reinforced composites (SRCs) is presented. In contrast to other investigations on back-injection of SRCs, a process is presented which allows compacting and back injection of SRCs in one step where the SRCs are partly consolidated only via melt pressure inside the cavity. The mechanical properties of SRCs depend to a large extent on the process parameters of temperature and pressure during manufacture. These parameters are not yet known for back-injected areas. Sensors ...
Aufsatz
Mechanical Characterization and Simulation of Wood Textile Composites (WTC) supported by Digital Image Correlation (DIC)
(2023-05-30)
Wood Textile Composites (WTC) based on willow wood fabrics and polypropylene were produced using a hot compacting process in order to open up new and innovative areas of applications for wood. Due to their attractive and variable design, the WTCs are to be used in areas with a high visual impact, for example as a facade element. In tensile and 3-point bending tests, it was shown that the mechanical properties of WTC are strongly dependent on the heterogeneous structure of the composite. Both strength and elongation ...
Aufsatz
Energy Resolved Residual Stress Analysis with Laboratory X-Ray Sources
(2017-04-17)
It is well known that existing residual stress fields play an important role for strength and lifetime of components. Consequently there is a great interest in the availability of fast, reliable and possibly nondestructive methods for their determination. In this context, X-ray diffraction methods play an important role in technical practice as well as in scientific research. They are based on the determination of lattice strains from which residual stresses are determined applying Hooke's law with appropriate elastic ...
Aufsatz
Prozessintegration von induktiver Wärmebehandlung und Festwalzen – sichere und zuverlässige Komponenten mit hoher Schwingfestigkeit
(2017-02-08)
Mechanische Oberflächenbehandlungen, beispielsweise das Festwalzen, spielen in der technischen Praxis eine bedeutende Rolle und tragen wesentlich zur Steigerung der Zuverlässigkeit hochbeanspruchter Komponenten bei. In einer Reihe von Fällen wurde gezeigt, dass eine Erhöhung der Prozesstemperatur die Wirksamkeit der Verfahren noch steigert, weil dies zu einer besseren Stabilisierung der eingebrachten Druckeigenspannungen führt. Eine wesentliche Voraussetzung zur Einführung dieser Verfahren in die Praxis ist allerdings, ...
Aufsatz
High Consistency Silicone Rubber Foams
(2024-04-23)
Silicone elastomers are high-performance plastics. In the extrusion process, only high-consistency silicone rubbers were used. In order to reduce the cost and weight, silicone rubbers can be foamed during processing. In this study, high-consistency silicone rubber is processed with different physical and chemical blowing agents. The resulting reaction kinetics, as well as the mechanical and morphological properties, had been investigated and compared with each other. This showed that the chemical blowing agent ...
Aufsatz
Effect of nanometric γ´-particles on the stress-induced martensitic transformation in ⟨001⟩-oriented Co49Ni21Ga30 shape memory alloy single crystals
(2019)
The effect of finely dispersed particles on the functional properties and morphology of thermally induced martensite in Co-Ni-Ga shape memory alloys has been already reported in literature, however, still important aspects are not fully understood. The current study focuses on the stress-induced martensitic transformation of solution-annealed, i.e. precipitate-free, and aged 〈001〉-oriented single crystals. In situ optical microscopy and neutron diffraction experiments show a significant influence of γ′-particles on ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...
Aufsatz
Characterization of wood-based multi-material systems under dynamic impact stress
(2018)
Due to its naturally grown properties, wood has played a rather subordinate role as a material for technical applications up to now. In this paper, multi-material systems based on veneers of beech (Fagus sylvatica) with different reinforcing variants were investigated. In addition to the influence of different adhesive systems (urea formaldehyde and polyurethane), the effect of reinforcing by aramid fiber fabric and stainless steel foil in different climates was examined. At the center of the investigations were ...