Suche
Anzeige der Dokumente 21-30 von 41
Aufsatz
A comparative study using water atomized and gas atomized powder in laser powder bed fusion process – Assessment of the fatigue performance
(2022)
Gas-atomized (GA, spherical) and water-atomized (WA, spattered) commercially pure iron (cp-Fe) powders were processed using laser-based powder bed fusion, resulting in a slightly higher porosity of the WA condition. In addition to characterization of quasi-static mechanical properties, fatigue tests, which are known to be detrimentally affected by porosity, were finally considered, revealing good properties even for the WA condition. In terms of microstructure stability, the GA and WA specimens significantly differ; ...
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...
Aufsatz
A Novel Approach to Robustly Determine Residual Stress in Additively Manufactured Microstructures Using Synchrotron Radiation
(2021-07-29)
In recent decades additive manufacturing (AM) for years has been in focus of academia and industry as its underlying production principle allows for the realization of designs of unprecedented geometrical complexity. However, often such structures are not realized due to the lack of understanding of structural and mechanical properties, this fact amongst others related to the unique microstructures established by the related processes. In this context, residual stresses, highly affected by the scan strategy and process ...
Aufsatz
Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys
(2021-07-26)
In situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is ...
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
Microstructural and mechanical properties of AlSi10Mg: Hybrid welding of additively manufactured and cast parts
(2022-12-07)
Welding and joining of hybrid components consisting of additively manufactured (AM) parts and conventionally processed parts offer new opportunities in structural design. In the present study, AlSi10Mg specimens were fabricated using two different manufacturing processes, i.e., laser-based powder-bed fusion of metals (PBF-LB/M) and casting, and welded by means of friction stir welding (FSW). Material strength of dissimilar welded joints was found to be governed by the as-cast material, which is characterized by a ...
Aufsatz
On the Influence of Surface Hardening Treatments on Microstructure Evolution and Residual Stress in Microalloyed Medium Carbon Steel
(2020-06-09)
Tailoring surface properties is a key to superior performance of components subjected to fatigue loadings in application. Process–microstructure–property relationships have to be established to allow for optimization of techniques employed for surface treatments such as deep rolling and induction hardening. Although both techniques are employed widely in industrial application, studies examining microstructure evolution and residual stress states for a single material in a comparative manner are missing. Amongst ...
Aufsatz
Influence of Microstructure and Defects on Mechanical Properties of AISI H13 Manufactured by Electron Beam Powder Bed Fusion
(2021-08-04)
Electron beam powder bed fusion (E-PBF) is a well-known additive manufacturing process. Components are realized based on layer-by-layer melting of metal powder. Due to the high degree of design freedom, additive manufacturing came into focus of tooling industry, especially for tools with sophisticated internal cooling channels. The present work focuses on the relationships between processing, microstructure evolution, chemical composition and mechanical properties of a high alloyed tool steel AISI H13 (1.2344, ...
Aufsatz
Evaluation of extremely steep residual stress gradients based on a combined approach using laboratory-scale equipment
(2021-11-30)
Surface treatments characterized by rapid heating and cooling (e.g. laser hardening) can induce very steep residual stress gradients in the direct vicinity of the area being treated. These gradients cannot be characterized with sufficient accuracy by means of the classical sin2Ψ approach applying angle-dispersive X-ray diffraction. This can be mainly attributed to limitations of the material removal method. In order to resolve residual stress gradients in these regions without affecting the residual stress equilibrium, ...