Search
Now showing items 1-10 of 18
Aufsatz
Martensite aging in ⟨001⟩ oriented Co₄₉ Ni₂₁ Ga₃₀ single crystals in tension
(2018-03-22)
Co–Ni–Ga high-temperature shape memory alloys (HT-SMAs) are well-known candidate materials for damping applications at elevated temperatures. Recent studies showed that upon heat treatment in stress-induced martensite under compressive loads transformation temperatures can be increased significantly, qualifying Co–Ni–Ga for HT-actuation. The increase in transformation temperatures is related to a change in chemical order recently validated via neutron diffraction experiments. Since SMAs show distinct tension–compression ...
Aufsatz
Electron beam welding of Fe–Mn–Al–Ni shape memory alloy: Microstructure evolution and shape memory response
(2017-07-03)
The present study reports on the impact of abnormal grain growth (AGG) on the microstructural evolution following electron beam (EB) welding of Fe–Mn–Al–Ni shape memory alloy (SMA). Polycrystalline sheet-like material was EB-welded and a cyclic heat treatment, studied in previous work, was conducted for inducing AGG and a bamboo-like microstructure, respectively. Optical and electron microscopy were carried out to characterize the prevailing microstructure upon cyclic heat treatment. For characterization of the ...
Aufsatz
Processing effects on tensile superelastic behaviour of Fe43.5Mn34Al15 ± XNi7.5∓X shape memory alloys
(2019)
Fe₄₃.₅Mn₃₄Al₁₅Ni₇.₅ was introduced in the current decade as a new superelastic alloy with great applicative potential due to: (i) superelastic behaviour over a thermal range of 200°C and (ii) recoverable strains up to 9.7 %. One of the key factors in enhancing the superelastic response of several shape memory alloys (SMAs) is the formation of an oligocrystalline structure, i.e. without triple junctions between grains, which is the result of an abnormal grain growth (AGG) process that can be induced by cyclic heat ...
Aufsatz
Design of novel materials for additive manufacturing - Isotropic microstructure and high defect tolerance
(2018-01-22)
Electron Beam Melting (EBM) is a powder-bed additive manufacturing technology enabling the production of complex metallic parts with generally good mechanical properties. However, the performance of powder-bed based additively manufactured materials is governed by multiple factors that are difficult to control. Alloys that solidify in cubic crystal structures are usually affected by strong anisotropy due to the formation of columnar grains of preferred orientation. Moreover, processing induced defects and porosity ...
Aufsatz
Shape memory effect and superelasticity in high-strength FeNiCoAlTi single crystals hardened by nanoparticles
(2019-11-19)
For [001]-oriented single crystals of Fe-28Ni-17Co-11.5Al-2.5Ti (at %) alloy in tension, it was shown that particles of the γ’-phase with a size of 4–6 nm lead to the appearance of superelasticity, with a strain of εSE=4.5% and a shape memory effect of εSME=5.9%. Increasing the particle size to 10–12 nm reduces εSE to 3.6% and εSME to 3.5%. The paper discusses the causes of the influence of particle size on the reversible strain.
Aufsatz
Cyclic Deformation Response of Ultra-fine Grained Titanium at Elevated Temperatures
(2019)
This study focuses on the high-temperature cyclic deformation response (CDR) of ultra-fine grained (UFG) titanium of commercial purity (grade 4) processed via equal channel angular extrusion as a severe plastic deformation method. Low-cycle fatigue experiments were conducted at elevated temperatures up to 600 °C and at strain amplitudes ranging from 0.2% to 0.6%. Besides temperature and strain amplitude, the influence of two processing routes (8BC and 8E) on the fatigue characteristics of UFG Ti was examined. It is ...
Aufsatz
Effect of nanometric γ´-particles on the stress-induced martensitic transformation in ⟨001⟩-oriented Co49Ni21Ga30 shape memory alloy single crystals
(2019)
The effect of finely dispersed particles on the functional properties and morphology of thermally induced martensite in Co-Ni-Ga shape memory alloys has been already reported in literature, however, still important aspects are not fully understood. The current study focuses on the stress-induced martensitic transformation of solution-annealed, i.e. precipitate-free, and aged 〈001〉-oriented single crystals. In situ optical microscopy and neutron diffraction experiments show a significant influence of γ′-particles on ...
Aufsatz
Wood-Polypropylene Composites: Influence of Processing on the Particle Shape and Size in Correlation with the Mechanical Properties Using Dynamic Image Analysis
(2018-11-16)
The particle size and shape are of momentous significance for the mechanical properties of plastic composites. However, natural fillers, like wood, are not consistent in these attributes. In order to investigate the shared traits between these characteristics, WPCs were produced using polypropylene, hardwood and softwood fillers with different particle sizes and a coupling agent. Afterwards, specimens were processed using an injection molding machine. The filler sizes and shapes were measured using dynamic image ...
Aufsatz
Characterization of Anisotropic Properties of Hot Compacted Self-Reinforced Composites (SRCs) via Thermal Diffusivity Measurement
(2019-11-01)
The mechanical properties of self-reinforced composites (SRCs) produced in a hot compaction process significantly depend on the process parameters. Only a little deviation of the process temperature or pressure causes the component to act differently under mechanical load. This is a chance and a challenge at the same time, since this process is difficult to handle but by properly controlling the process parameters, the mechanical properties can be adjusted, even locally for one component. In this research SRC are ...
Aufsatz
A Closer Look at the Bonding Capacity of Thick Metal-Plastic Hybrids
(2019-03-01)
Metal-plastic hybrids have a lot of advantages compared to purely metal or purely plastic parts. A good design for metal-plastic hybrids can help to save weight, for example in automotive applications. Therefore, it is important to understand the joining mechanisms between both materials. Aluminum AlSi9Cu3(Fe) and polyamide 6.6 with 35 % glass fibers were used as joining partners. The materials were joined by enclosing the metal part at least partially with plastic right inside the injection molding tool. Afterwards, ...