Suche
Anzeige der Dokumente 1-10 von 28
Aufsatz
Comparative investigation of two-dimensional imaging methods and X-ray tomography in the characterization of microstructure
(2017-10-02)
The microstructural features of three different materials have been quantified by means of 2D image analysis and X-ray micro-computer tomography (CT) and the results were compared to determine the reliability of the 2D analysis in the material characterization. The 3D quantification of shrinkage pores and Fe-rich inclusions of an Al-Si-Cu alloy by X-ray tomography was compared with the statistical analysis of the 2D metallographic pictures and a significant difference in the results was found due to the complex ...
Aufsatz
Martensite aging in ⟨001⟩ oriented Co₄₉ Ni₂₁ Ga₃₀ single crystals in tension
(2018-03-22)
Co–Ni–Ga high-temperature shape memory alloys (HT-SMAs) are well-known candidate materials for damping applications at elevated temperatures. Recent studies showed that upon heat treatment in stress-induced martensite under compressive loads transformation temperatures can be increased significantly, qualifying Co–Ni–Ga for HT-actuation. The increase in transformation temperatures is related to a change in chemical order recently validated via neutron diffraction experiments. Since SMAs show distinct tension–compression ...
Aufsatz
Electron beam welding of Fe–Mn–Al–Ni shape memory alloy: Microstructure evolution and shape memory response
(2017-07-03)
The present study reports on the impact of abnormal grain growth (AGG) on the microstructural evolution following electron beam (EB) welding of Fe–Mn–Al–Ni shape memory alloy (SMA). Polycrystalline sheet-like material was EB-welded and a cyclic heat treatment, studied in previous work, was conducted for inducing AGG and a bamboo-like microstructure, respectively. Optical and electron microscopy were carried out to characterize the prevailing microstructure upon cyclic heat treatment. For characterization of the ...
Aufsatz
Processing effects on tensile superelastic behaviour of Fe43.5Mn34Al15 ± XNi7.5∓X shape memory alloys
(2019)
Fe₄₃.₅Mn₃₄Al₁₅Ni₇.₅ was introduced in the current decade as a new superelastic alloy with great applicative potential due to: (i) superelastic behaviour over a thermal range of 200°C and (ii) recoverable strains up to 9.7 %. One of the key factors in enhancing the superelastic response of several shape memory alloys (SMAs) is the formation of an oligocrystalline structure, i.e. without triple junctions between grains, which is the result of an abnormal grain growth (AGG) process that can be induced by cyclic heat ...
Aufsatz
Design of novel materials for additive manufacturing - Isotropic microstructure and high defect tolerance
(2018-01-22)
Electron Beam Melting (EBM) is a powder-bed additive manufacturing technology enabling the production of complex metallic parts with generally good mechanical properties. However, the performance of powder-bed based additively manufactured materials is governed by multiple factors that are difficult to control. Alloys that solidify in cubic crystal structures are usually affected by strong anisotropy due to the formation of columnar grains of preferred orientation. Moreover, processing induced defects and porosity ...
Aufsatz
Shape memory effect and superelasticity in high-strength FeNiCoAlTi single crystals hardened by nanoparticles
(2019-11-19)
For [001]-oriented single crystals of Fe-28Ni-17Co-11.5Al-2.5Ti (at %) alloy in tension, it was shown that particles of the γ’-phase with a size of 4–6 nm lead to the appearance of superelasticity, with a strain of εSE=4.5% and a shape memory effect of εSME=5.9%. Increasing the particle size to 10–12 nm reduces εSE to 3.6% and εSME to 3.5%. The paper discusses the causes of the influence of particle size on the reversible strain.
Aufsatz
Cyclic Deformation Response of Ultra-fine Grained Titanium at Elevated Temperatures
(2019)
This study focuses on the high-temperature cyclic deformation response (CDR) of ultra-fine grained (UFG) titanium of commercial purity (grade 4) processed via equal channel angular extrusion as a severe plastic deformation method. Low-cycle fatigue experiments were conducted at elevated temperatures up to 600 °C and at strain amplitudes ranging from 0.2% to 0.6%. Besides temperature and strain amplitude, the influence of two processing routes (8BC and 8E) on the fatigue characteristics of UFG Ti was examined. It is ...
Aufsatz
Energy Resolved Residual Stress Analysis with Laboratory X-Ray Sources
(2017-04-17)
It is well known that existing residual stress fields play an important role for strength and lifetime of components. Consequently there is a great interest in the availability of fast, reliable and possibly nondestructive methods for their determination. In this context, X-ray diffraction methods play an important role in technical practice as well as in scientific research. They are based on the determination of lattice strains from which residual stresses are determined applying Hooke's law with appropriate elastic ...
Aufsatz
Prozessintegration von induktiver Wärmebehandlung und Festwalzen – sichere und zuverlässige Komponenten mit hoher Schwingfestigkeit
(2017-02-08)
Mechanische Oberflächenbehandlungen, beispielsweise das Festwalzen, spielen in der technischen Praxis eine bedeutende Rolle und tragen wesentlich zur Steigerung der Zuverlässigkeit hochbeanspruchter Komponenten bei. In einer Reihe von Fällen wurde gezeigt, dass eine Erhöhung der Prozesstemperatur die Wirksamkeit der Verfahren noch steigert, weil dies zu einer besseren Stabilisierung der eingebrachten Druckeigenspannungen führt. Eine wesentliche Voraussetzung zur Einführung dieser Verfahren in die Praxis ist allerdings, ...
Aufsatz
Effect of nanometric γ´-particles on the stress-induced martensitic transformation in ⟨001⟩-oriented Co49Ni21Ga30 shape memory alloy single crystals
(2019)
The effect of finely dispersed particles on the functional properties and morphology of thermally induced martensite in Co-Ni-Ga shape memory alloys has been already reported in literature, however, still important aspects are not fully understood. The current study focuses on the stress-induced martensitic transformation of solution-annealed, i.e. precipitate-free, and aged 〈001〉-oriented single crystals. In situ optical microscopy and neutron diffraction experiments show a significant influence of γ′-particles on ...