Suche
Anzeige der Dokumente 121-130 von 150
Aufsatz
Liquid Silicone Rubber Foams Made with Water as Blowing Agent
(2021-08-18)
Liquid silicone rubber (LSR) is primarily used in injection molding. Foamed molded parts made of LSR are almost nonexistent because the process reliability of LSR foam injection molding is currently not given. It makes sense to have suitable foaming processes for this material as well, because the density of this elastomer is about 1.15 g cm−3. With the injection molding process presented herein for foaming LSR, density reductions of up to 40% can be achieved. In this process, up to 3% by weight of water is added to ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...
Aufsatz
On the Impact of Build Envelope Sizes on E-PBF Processed Pure Iron
(2021-11-17)
In additive manufacturing, the thermal history of a part determines its final microstructural and mechanical properties. The factors leading to a specific temperature profile are diverse. For the integrity of a parameter setting established, periphery variations must also be considered. In the present study, iron was processed by electron beam powder bed fusion. Parts realized by two process runs featuring different build plate sizes were analyzed. It is shown that the process temperature differs significantly, ...
Aufsatz
On the Microstructural and Cyclic Mechanical Properties of Pure Iron Processed by Electron Beam Melting
(2021-03-10)
Additive manufacturing (AM) processes such as electron beam melting (EBM) are characterized by unprecedented design freedom. Topology optimization and design of the microstructure of metallic materials are enabled by rapid progress in this field. The latter is of highest importance as many applications demand appropriate mechanical as well as functional material properties. For instance, biodegradable implants have to meet mechanical properties of human bone and at the same time guarantee adequate cytocompatibility ...
Aufsatz
CuCrZr processed by laser powder bed fusion — Processability and influence of heat treatment on electrical conductivity, microstructure and mechanical properties
(2021-06-16)
CuCrZr parts were fabricated by laser beam powder bed fusion (LB-PBF) technique and subjected to different heat treatments. As a result, four different conditions were considered for further investigations, that is, the as-built condition, conditions of maximum hardness (MH) and maximum electrical conductivity (MC), and a condition representing a compromise between hardness and conductivity (H&C). Microstructural evolution and performance under monotonic and cyclic loading were studied. Fracture surfaces revealed ...
Aufsatz
Thermal Stability of Residual Stresses in Differently Deep Rolled Surface Layers of Steel SAE 1045
(2021-05-07)
The stability of compressive residual stresses generated by deep rolling plays a decisive role on the fatigue behavior of specimens and components, respectively. In this regard, deep rolling at elevated temperature has proven to be very effective in stabilizing residual stresses when fatigue analysis is conducted at ambient temperature. However, since residual stresses can be affected not only by plastic deformation but also when thermal energy is provided, it is necessary to analyze the influence of temperature and ...
Aufsatz
Additive Manufacturing of Compositionally-Graded AISI 316L to CoCrMo Structures by Directed Energy Deposition
(2021-08-30)
In the present study, compositionally-graded structures of AISI 316L and CoCrMo alloy are manufactured by powder-based laser-beam directed energy deposition (DED-LB). Through a process-integrated adjustment of powder flow, in situ alloying of the two materials becomes feasible. Thus, a sharp and a smooth transition with a mixture of both alloys can be realized. In order to investigate the phase formation during in situ alloying, a simulation approach considering equilibrium calculations is employed. The findings ...
Aufsatz
Evaluation of extremely steep residual stress gradients based on a combined approach using laboratory-scale equipment
(2021-11-30)
Surface treatments characterized by rapid heating and cooling (e.g. laser hardening) can induce very steep residual stress gradients in the direct vicinity of the area being treated. These gradients cannot be characterized with sufficient accuracy by means of the classical sin2Ψ approach applying angle-dispersive X-ray diffraction. This can be mainly attributed to limitations of the material removal method. In order to resolve residual stress gradients in these regions without affecting the residual stress equilibrium, ...
Aufsatz
Time-of-Flight Three Dimensional Neutron Diffraction in Transmission Mode for Mapping Crystal Grain Structures
(2017-08-25)
The physical properties of polycrystalline materials depend on their microstructure, which is the nano- to centimeter scale arrangement of phases and defects in their interior. Such microstructure depends on the shape, crystallographic phase and orientation, and interfacing of the grains constituting the material. This article presents a new non-destructive 3D technique to study centimeter-sized bulk samples with a spatial resolution of hundred micrometers: time-of-flight three-dimensional neutron diffraction (ToF ...
Aufsatz
Dynamic Tensile Deformation of High Strength Aluminum Alloys Processed Following Novel Thermomechanical Treatment Strategies
(2020-05-14)
Herein, the effects of a very recently introduced novel thermomechanical process route on the microstructural evolution and dynamic tensile deformation behavior of two different precipitation hardenable aluminum alloys, i.e., AA6082 and AA7075, are studied. The investigated materials are hot formed and quenched in differently tempered tools to reveal the influence of cooling rate. Microstructure analysis is conducted to study the influences of different cooling strategies on the microstructure evolution and prevailing ...