Suche
Anzeige der Dokumente 71-78 von 78
Konferenzveröffentlichung
Blending CA with PBS to increase the bonding strength in two-component injection molding
(Society of Plastics Engineers, 2019)
Since CA shows no adhesive properties in the two-component injection molding process with bio based TPU, blends of CA and PBS were produced to decrease the interfacial tension between the materials. While the interfacial tension was calculated from the results of a drop shape analysis, the adhesion strength was measured in peel tests according to the guideline VDI 2019. The comparison of the results gave information about whether the drop shape analysis is a valid method to analyze the adhesive characteristics of ...
Konferenzveröffentlichung
Natural fiber reinforced technical (bio-) composites modified with halogen-free flame retardants
(Society of Plastics Engineers, 2019)
Under the aspect of sustainability and the use of alternative materials, engineering thermoplastics such as polybutylene terephthalate (PBT) will be reinforced with renewable raw materials such as regenerated cellulose fibers.
The University of Kassel is developing cellulose regenerated fiber reinforced technical thermoplastics in a state-funded project with further companies. Since pure natural fibers cannot withstand the high operating temperature of engineering thermoplastics (Ts>230°C), regenerated cellulose ...
Aufsatz
Effect of nanometric γ´-particles on the stress-induced martensitic transformation in ⟨001⟩-oriented Co49Ni21Ga30 shape memory alloy single crystals
(2019)
The effect of finely dispersed particles on the functional properties and morphology of thermally induced martensite in Co-Ni-Ga shape memory alloys has been already reported in literature, however, still important aspects are not fully understood. The current study focuses on the stress-induced martensitic transformation of solution-annealed, i.e. precipitate-free, and aged 〈001〉-oriented single crystals. In situ optical microscopy and neutron diffraction experiments show a significant influence of γ′-particles on ...
Aufsatz
Wood-Polypropylene Composites: Influence of Processing on the Particle Shape and Size in Correlation with the Mechanical Properties Using Dynamic Image Analysis
(2018-11-16)
The particle size and shape are of momentous significance for the mechanical properties of plastic composites. However, natural fillers, like wood, are not consistent in these attributes. In order to investigate the shared traits between these characteristics, WPCs were produced using polypropylene, hardwood and softwood fillers with different particle sizes and a coupling agent. Afterwards, specimens were processed using an injection molding machine. The filler sizes and shapes were measured using dynamic image ...
Aufsatz
Characterization of wood-based multi-material systems under dynamic impact stress
(2018)
Due to its naturally grown properties, wood has played a rather subordinate role as a material for technical applications up to now. In this paper, multi-material systems based on veneers of beech (Fagus sylvatica) with different reinforcing variants were investigated. In addition to the influence of different adhesive systems (urea formaldehyde and polyurethane), the effect of reinforcing by aramid fiber fabric and stainless steel foil in different climates was examined. At the center of the investigations were ...
Aufsatz
Cross-Linked Hydrophobic Starch Granules in Blends with PLA
(2018-04-17)
The majority of native starch is used in the food sector and in the paper industry. Only a small amount is used in polymer engineering. One reason for the reluctance of the plastics processing industry to use starch as a filling material in polymer blends is the unsatisfactory mechanical behavior of starch when combined with thermoplastics. Another reason is the hydrophilicity of starch. In order to make these materials capable of competing, an amelioration of the mechanical properties is compulsory. By means of ...
Konferenzveröffentlichung
UV light irradiation of fibers in thermoplastic pultrusion for higher surface energy
(Society of Plastics Engineers, 2018)
Pultrusion is a common way to produce thermoplastic composites reinforced with different kinds of fibers. There are many different opportunities to improve the properties of a thermoplastic material. Different kind of fibers where pultruded in combination with different thermoplastic materials. The fiber content was set to 30wt% comparing the roving strain with the pultruded strain. UV-C light was used in the process to improve the fiber matrix adhesion. The pultruded strain was granulated and injection molded to ...