Suche
Anzeige der Dokumente 21-30 von 44
Aufsatz
On the structural integrity of Fe-36Ni Invar alloy processed by selective laser melting
(2020)
Specimens made from pre-alloyed Invar (Fe-36Ni) powder were fabricated by selective laser melting and stress-relief heat treated afterwards. A relative density of the fabricated parts of 99.6 % was determined by computed tomography. The microstructure and mechanical behavior under monotonic and particularly cyclic loading at ambient temperature were investigated. Results reveal a bimodal microstructure containing columnar and equiaxed grains with an average grain size of 75 μm and pronounced texture 〈001〉 || BD. The ...
Aufsatz
Dynamic Tensile Deformation of High Strength Aluminum Alloys Processed Following Novel Thermomechanical Treatment Strategies
(2020-05-14)
Herein, the effects of a very recently introduced novel thermomechanical process route on the microstructural evolution and dynamic tensile deformation behavior of two different precipitation hardenable aluminum alloys, i.e., AA6082 and AA7075, are studied. The investigated materials are hot formed and quenched in differently tempered tools to reveal the influence of cooling rate. Microstructure analysis is conducted to study the influences of different cooling strategies on the microstructure evolution and prevailing ...
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
(2022-03-03)
In this research paper, the effects of the combined compacting and back-injection process to produce back-injected self-reinforced composites on the mechanical properties of the self-reinforced composites (SRCs) are investigated. For this purpose, the parameters barrel temperature, time of injection and holding pressure were varied for the back injection. Tensile and bending tests were carried out on the SRCs. The results show that the mechanical properties depend to a large extent on the process parameters. The ...
Aufsatz
On the Monotonic and Cyclic Behavior of an Al-Mg-Zn-Cu-Si Compositionally Complex Alloy
(2023-08-03)
In present work, the monotonic and cyclic properties of a novel Al-Mg-Zn-Cu-Si compositionally complex alloy (CCA) are investigated. Microstructural studies reveal that a eutectic phase and fishbone-type structures are embedded in the Al-matrix. The mechanical properties of this CCA obtained under compressive loading are found to be promising. However, low ultimate strength and brittle behavior are seen under tension. The fatigue performance of the alloy in the low-cycle fatigue (LCF) regime is poor. Microstructural ...
Aufsatz
Experimental Analysis of the Stability of Retained Austenite in a Low-Alloy 42CrSi Steel after Different Quenching and Partitioning Heat Treatments
(2023-06-21)
Quenching and partitioning (Q&P) steels are characterized by an excellent combination of strength and ductility, opening up great potentials for advanced lightweight components. The Q&P treatment results in microstructures with a martensitic matrix being responsible for increased strength whereas interstitially enriched metastable retained austenite (RA) contributes to excellent ductility. Herein, a comprehensive experimental characterization of microstructure evolution and austenite stability is carried out on a ...
Aufsatz
Electron Beam Welding of Hot-Rolled Fe–Mn–Al–Ni Shape Memory Alloy Sheets
(2023-04-25)
The present study focuses on the weldability of hot-rolled Fe–Mn–Al–Ni shape memory alloy sheets by vacuum electron beam welding. Tailored process-specific welding parameters, such as preheating with electron beam or beam oscillation during welding, allowed defect-free joining with very thin weld seams and heat-affected zones. By applying a post-weld cyclic heat treatment, abnormal grain growth can be promoted across the weld seams. However, regardless of the selected welding parameters, some specimens are characterized ...
Aufsatz
Low-Cycle-Fatigue Performance of Stress-Aged EN AW-7075 Alloy
(2023-05-05)
The effect of a novel heat treatment, that is, aging under superimposed external stress, on the fatigue performance and microstructural evolution of a high-strength aluminum alloy (EN AW-7075) is presented. Stress aging, a combination of heat treatment and superimposed external stress, can enhance the mechanical properties of EN AW-7075 under monotonic loading due to the acceleration of precipitation kinetics. Scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) reveal that a longer ...
Aufsatz
UVC Irradiation as a Surface Treatment of Polycarbonate to Generate Adhesion to Liquid Silicone Rubber in an Overmolding Process
(2024-04-18)
This study investigates the adhesion properties of polycarbonate (PC) and liquid silicone rubbers (LSR) through surface activation using ultraviolet C (UVC) radiation. While self-adhesive LSRs adhere easily to certain thermoplastic composites such as polybutylene terephthalate (PBT) and polyamides (PAs), bonding to PC typically requires surface treatment due to the lack of compatible functional groups. Previous methods like plasma or flame treatment have been effective, but the use of UVC radiation for surface ...
Aufsatz
Characterization of Mechanical Properties, Macroscopic Deformation Behavior, and Microstructure of Functionally Graded 22MnB5 Steel
(2021-03-24)
The focus of this study is on the characterization of the local plastic deformation and failure of functionally graded 22MnB5 plates after hot stamping using an in situ approach. Various forming strategies at elevated temperatures are performed using differentially tempered forming tools to locally tailor the microstructure. By controlling the cooling rate, graded as well as martensitic and ferritic–pearlitic microstructures are obtained. Experimental analysis includes evaluation of the material- and geometry-dependent ...