Search
Now showing items 51-60 of 71
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Pathways toward the Use of Non-Destructive Micromagnetic Analysis for Porosity Assessment and Process Parameter Optimization in Additive Manufacturing of 42CrMo4 (AISI 4140)
(2024-02-20)
Laser-based powder bed fusion of metals (PBF-LB/M) is a widely applied additive manufacturing technique. Thus, PBF-LB/M represents a potential candidate for the processing of quenched and tempered (Q&T) steels such as 42CrMo4 (AISI 4140), as these steels are often considered as the material of choice for complex components, e.g., in the toolmaking industry. However, due to the presence of process-induced defects, achieving a high quality of the resulting parts remains challenging in PBF-LB/M. Therefore, an extensive ...
Aufsatz
Bend Straightening of a Carbonitrided Gear Shaft – Consequences on Residual Stresses and Retained Austenite near the Surface
(2017-06-20)
Carbonitriding of shafts in drive technology is strongly connected with distortion. Bend straightening is an important process step in order to eliminate distortion without removing the hardened surface layer. As shown in several investigations, even for simple part geometries, bending induced stresses and plastic deformations have a strong impact not only on the residual stress state but also on the microstructure after straightening. As gear shafts become increasingly filigree and complex in their geometry, the ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
On the Influence of Microstructure on the Corrosion Behavior of Fe–Mn–Al–Ni Shape Memory Alloy in 5.0 wt% NaCl Solution
(2020-10-03)
Herein the corrosion behavior of Fe–Mn–Al–Ni shape memory alloys characterized by different microstructures in a 5.0 wt% NaCl solution is investigated. Open circuit potential and potentiodynamic polarisation tests are conducted. Generally, Fe–Mn–Al–Ni shows corrosion properties being similar to pure iron. However, the polarization curves of single crystals indicate the presence of an unstable passive system. The corrosion damage is analyzed by means of optical microscopy and electron microscopy. It is revealed that ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Investigation of residual stresses in polypropylene using hot plate welding
(2020-08-05)
During the cooling process of the molten material, residual stresses appear because the reduced volume of the cooled material cannot fully fill the space formerly occupied by the molten material. The morphology in and around the weld is formed by different factors depending on the material and process parameters. Different morphological structures relate to different mechanical properties. The process parameters and the welding results including morphology and residual stress are linked together. In this article, ...
Aufsatz
Influence of the degree of crystallinity and the surface free energy on the adhesion properties of different PLA/PBS blends in multicomponent injection molding
(2020-01-10)
Biocomposites made of biodegradable polymers have grown in interest due to their environmentally friendliness, considering that non-biodegradable polymers waste conduces to pollution, displaying high environmental impact in climatic changes. Therefore, in the presented study, biodegradable Poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) were investigated as a series of PLA/PBS melt-blending compounds with the weight ratios of 50/50, 60/40, 70/30, 80/20 and 90/10. In a two-component injection molding ...
Aufsatz
Mechanical properties of hybrid glass/kenaf fibre-reinforced epoxy composite with matrix modification using liquid epoxidised natural rubber
(2015-04-27)
The hybridisation of natural fibre with glass fibre provides a method to improve the mechanical properties instead of using the natural fibres alone. This research is focused on the hybridisation of glass/kenaf fibre with the addition of liquid epoxidised natural rubber to enhance the desired mechanical properties of the composite by reducing the synthetic fibre usage and encourage the natural fibre consumption. Liquid epoxidised natural rubber was added to the epoxy matrix in order to improve its mechanical properties ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Parameter identification for constitutive models of innovative textile composite materials using digital image correlation
(2019-11-18)
This contribution focuses on an innovative composite material consisting of textile layers made from continuous wooden fibers embedded in a thermoplastic matrix. A finite element simulation of potential use‐cases is planned to support the development process and to study the suitability of the material in an architectural context. The simulation is based on a constitutive model assuming homogenous orthotropic elastic behavior and will be expanded to include multiscale modeling in future research. The material parameters ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
A Comparison Study of Liquid Natural Rubber (LNR) and Liquid Epoxidized Natural Rubber (LENR) as the Toughening Agent for Epoxy
(2013)
Rubber-toughened epoxy resins were prepared using the mechanical stirring method and molded into samples by compression molding. The aim of this study is to modify the brittleness of the epoxy matrix by adding discrete rubbery phases to improve the toughness properties. Liquid natural rubber (LNR) and liquid epoxidized natural rubber (LENR) were used as toughening agents in the epoxy resin to compare the properties of the modified networks. The mechanical and thermal properties have been studied to observe the effect ...
Aufsatz
Morphology-property-relationship of thermo-mechanically graded self-reinforced polypropylene composites
(2015-02-17)
In this paper the relationship between different composite morphologies and their mechanical properties is to be investigated. By manufacturing two different tape-based polypropylene composites in a compression moulding process, four varying degrees of compaction will be generated. The morphological structure is analyzed using confocal laser light microscopy and wet chemically etched specimen cross-sections. The etching process removes the amorphous phase in the polymer, making the macromolecular orientations and ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Crack path predictions in fiber reinforced composites
(2017-09-06)
Composite materials exhibit beneficial features compared to conventional engineering material, e.g. a comparable strength and a reduced weight at the same time. To fully exploit these beneficial properties within technical structures, fracture mechanical concepts must be taken into account. The global fracture behavior in composite materials is related to the local delamination at interfaces between matrix and inclusion as well as the local fracture behaviors of the constituents. Because of their structure, the global ...