Suche
Anzeige der Dokumente 31-40 von 78
Aufsatz
Cyclic Deformation Response of Ultra-fine Grained Titanium at Elevated Temperatures
(2019)
This study focuses on the high-temperature cyclic deformation response (CDR) of ultra-fine grained (UFG) titanium of commercial purity (grade 4) processed via equal channel angular extrusion as a severe plastic deformation method. Low-cycle fatigue experiments were conducted at elevated temperatures up to 600 °C and at strain amplitudes ranging from 0.2% to 0.6%. Besides temperature and strain amplitude, the influence of two processing routes (8BC and 8E) on the fatigue characteristics of UFG Ti was examined. It is ...
Aufsatz
Effect of grain size on the very high cycle fatigue behavior and notch sensitivity of titanium
(2019)
The very high-cycle fatigue performances of coarse-grained and ultrafine-grained titanium samples with different geometries at ambient temperature and various stress amplitudes were investigated. Severe plastic deformation improves monotonic strength of titanium at the cost of a loss in ductility. Ultrafine-grained titanium demonstrates a superior fatigue performance compared to that of coarse-grained counterparts in the high-cycle fatigue regime, however, suffers notch sensitivity. Furthermore, in the very high-cycle ...
Aufsatz
Influence of deep rolling at different temperatures on near-surface and mechanical properties of a Maraging C250 steel
(2024-04-27)
Due to an outstanding combination of high strength and fracture toughness Maraging steels are used in numerous industries, e.g., in the aerospace sector. The high strength can be attributed to precipitation strengthening by conventional age-hardening heat treatments. However, as many of the envisaged applications will suffer from cyclic loadings, the fatigue properties are of significant interest in terms of a reliable use. Generally, Maraging steels are characterized by a relatively low fatigue strength limiting the ...
Aufsatz
Oxide Modified Iron in Electron Beam Powder Bed Fusion - From Processability to Corrosion Properties
(2022-03-07)
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material composition, and the solidification behavior of the material considered. However, when complex specific requirements have to be met, a targeted part design is highly challenging. In the field of biodegradable implant surgery, a cytocompatible material of an application-adapted ...
Aufsatz
Energy Resolved Residual Stress Analysis with Laboratory X-Ray Sources
(2017-04-17)
It is well known that existing residual stress fields play an important role for strength and lifetime of components. Consequently there is a great interest in the availability of fast, reliable and possibly nondestructive methods for their determination. In this context, X-ray diffraction methods play an important role in technical practice as well as in scientific research. They are based on the determination of lattice strains from which residual stresses are determined applying Hooke's law with appropriate elastic ...
Aufsatz
Prozessintegration von induktiver Wärmebehandlung und Festwalzen – sichere und zuverlässige Komponenten mit hoher Schwingfestigkeit
(2017-02-08)
Mechanische Oberflächenbehandlungen, beispielsweise das Festwalzen, spielen in der technischen Praxis eine bedeutende Rolle und tragen wesentlich zur Steigerung der Zuverlässigkeit hochbeanspruchter Komponenten bei. In einer Reihe von Fällen wurde gezeigt, dass eine Erhöhung der Prozesstemperatur die Wirksamkeit der Verfahren noch steigert, weil dies zu einer besseren Stabilisierung der eingebrachten Druckeigenspannungen führt. Eine wesentliche Voraussetzung zur Einführung dieser Verfahren in die Praxis ist allerdings, ...
Aufsatz
Effect of nanometric γ´-particles on the stress-induced martensitic transformation in ⟨001⟩-oriented Co49Ni21Ga30 shape memory alloy single crystals
(2019)
The effect of finely dispersed particles on the functional properties and morphology of thermally induced martensite in Co-Ni-Ga shape memory alloys has been already reported in literature, however, still important aspects are not fully understood. The current study focuses on the stress-induced martensitic transformation of solution-annealed, i.e. precipitate-free, and aged 〈001〉-oriented single crystals. In situ optical microscopy and neutron diffraction experiments show a significant influence of γ′-particles on ...
Aufsatz
Effects of aging on the stress-induced martensitic transformation and cyclic superelastic properties in Co-Ni-Ga shape memory alloy single crystals under compression
(2022)
Co-Ni-Ga shape memory alloys attracted scientific attention as promising candidate materials for damping applications at elevated temperatures, owing to excellent superelastic properties featuring a fully reversible stress-strain response up to temperatures as high as 500 °C. In the present work, the effect of aging treatments conducted in a wide range of aging temperatures and times, i.e. at 300–400 °C for 0.25–8.5 h, was investigated. It is shown that critical features of the martensitic transformation are strongly ...
Aufsatz
Additive manufacturing of Co-Ni-Ga high-temperature shape memory alloy - Processability 3 and phase transformation behavior
(2019)
Co-Ni-Ga high-temperature shape memory alloy is additively processed by selective laser melting for the first time. Reversiblemartensitic transformation of the as-built material is proven by differential scanning calorimetry. Microstructural analysis reveals a columnar-grained microstructure due to epitaxial solidification. Columnar-grained microstructures are characterized by a very low degree of constraints being beneficial for superior functional performance in numerous shape memory alloys. However, process-induced ...
Aufsatz
Microstructure of an additively manufactured Ti-Ta-Al alloy using novel pre-alloyed powder feedstock material
(2023-05-01)
Binary Ti-Ta and ternary Ti-Ta-Al alloys attracted considerable attention as new potential biomaterials and/or high-temperature shape memory alloys. However, conventional forming and manufacturing technologies of refractory based titanium alloys are difficult and cost-intensive, especially when complex shapes are required. Recently, additive manufacturing (AM) emerged as a suitable alternative and several studies exploited elemental powder mixing approaches to obtain a desired alloy and subsequently use it for complex ...