Suche
Anzeige der Dokumente 41-50 von 53
Buch
Struktur-Eigenschafts-Beziehung von Mischungen aus thermoplastischem PMMA mit vernetzten PMMA-Kolloiden
(kassel university press, 2016)
Ziel dieser Arbeit war es, ein Compound aus Partikeln aus untereinander vernetzten Polymerketten, sogenannten Kolloiden, und thermoplastischem Matrixmaterial basierend auf dem gleichen Monomer (MMA) aus ingenieurwissenschaftlicher Sicht zu charakterisieren und die Struktur-Eigenschafts-Beziehungen zu klären. Durchgeführt wurden die Untersuchungen an Compounds mit Kolloiden mit verschiedenen Größen, Vernetzungsgraden und Anteilen, die zunächst in Benzol mit dem Matrixmaterial, Plexiglas® 6N, vermischt wurden.
Neben ...
Konferenzveröffentlichung
Multicomponent Injection Molding Of Thermoplastics And Liquid Silicone Rubber (LSR) – Either Cured By Heat Or UV Light
(Society of Plastics Engineers, 2016)
For processing thermally curing liquid silicone rubber (LSR) as well as UV light curing LSR for multicompo-nent injection molding with thermoplastics in an compa-rable way a processing center was designed and set into operation.
For the production of the multicomponent specimens a modular tool was designed. In there a thermoplastic plate gets molded on the one side, then gets transferred auto-matically by a robot system and gets overmolded by the silicone on the other side. The complete silicone side of the tool is ...
Aufsatz
Parameter identification for constitutive models of innovative textile composite materials using digital image correlation
(2019-11-18)
This contribution focuses on an innovative composite material consisting of textile layers made from continuous wooden fibers embedded in a thermoplastic matrix. A finite element simulation of potential use‐cases is planned to support the development process and to study the suitability of the material in an architectural context. The simulation is based on a constitutive model assuming homogenous orthotropic elastic behavior and will be expanded to include multiscale modeling in future research. The material parameters ...
Aufsatz
Climatic Ageing of Components of Polymer Based Electrochromic Devices
(2013-09-09)
Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity ...
Aufsatz
UV Surface Treatment of Polycarbonate for Adhesion Improvement to Liquid Silicone Rubber (LSR)
(2018)
The adhesion of self-adhesive liquid silicone rubbers to thermoplasts is only possible for a few selected material combinations without a surface pretreatment. A UV pretreatment is effective for polycarbonate and short irradiation periods are sufficient. To clarify the required irradiation conditions that result in an improvement of adhesion, the varying irradiation conditions were assessed. FTIR-ATR spectroscopy was used for surface analysis to characterize the change in the polymer surface.
Aufsatz
Characterization of Anisotropic Properties of Hot Compacted Self-Reinforced Composites (SRCs) via Thermal Diffusivity Measurement
(2019-11-01)
The mechanical properties of self-reinforced composites (SRCs) produced in a hot compaction process significantly depend on the process parameters. Only a little deviation of the process temperature or pressure causes the component to act differently under mechanical load. This is a chance and a challenge at the same time, since this process is difficult to handle but by properly controlling the process parameters, the mechanical properties can be adjusted, even locally for one component. In this research SRC are ...
Aufsatz
A Closer Look at the Bonding Capacity of Thick Metal-Plastic Hybrids
(2019-03-01)
Metal-plastic hybrids have a lot of advantages compared to purely metal or purely plastic parts. A good design for metal-plastic hybrids can help to save weight, for example in automotive applications. Therefore, it is important to understand the joining mechanisms between both materials. Aluminum AlSi9Cu3(Fe) and polyamide 6.6 with 35 % glass fibers were used as joining partners. The materials were joined by enclosing the metal part at least partially with plastic right inside the injection molding tool. Afterwards, ...
Aufsatz
UV Pre-Treatment for Polycarbonate for Bonding LSR in a Multi-Component Injection Molding Process
(2019-03-01)
In this study, the influence of UVC radiation and the influence of ozone on the surface energy of specimens made of polycarbonate were investigated. In an additional step, the peeling resistance of silicone flaps, which were overmolded, onto pre-treated PC plates of multicomponent specimens were analyzed. For this purpose, the samples were exposed to UVC radiation for different lengths of time, ranging from 5 s to 3 600 s. To further evaluate the influence of the ozone created by the UVC in the presence of oxygen, ...
Aufsatz
Characterization of wood-based multi-material systems under dynamic impact stress
(2018)
Due to its naturally grown properties, wood has played a rather subordinate role as a material for technical applications up to now. In this paper, multi-material systems based on veneers of beech (Fagus sylvatica) with different reinforcing variants were investigated. In addition to the influence of different adhesive systems (urea formaldehyde and polyurethane), the effect of reinforcing by aramid fiber fabric and stainless steel foil in different climates was examined. At the center of the investigations were ...
Aufsatz
Cross-Linked Hydrophobic Starch Granules in Blends with PLA
(2018-04-17)
The majority of native starch is used in the food sector and in the paper industry. Only a small amount is used in polymer engineering. One reason for the reluctance of the plastics processing industry to use starch as a filling material in polymer blends is the unsatisfactory mechanical behavior of starch when combined with thermoplastics. Another reason is the hydrophilicity of starch. In order to make these materials capable of competing, an amelioration of the mechanical properties is compulsory. By means of ...