Suche
Anzeige der Dokumente 21-30 von 56
Aufsatz
Mechanical Properties of Polydimethylsiloxane as a Function of the Amount and Type of Crosslinking Agent
(2017-06-13)
In this investigation, a high-consistency rubber (HCR) was mixed with five different, typically used crosslinking agents that are based on organic peroxide. Furthermore, the amount of crosslinking agent was varied in order to quantify the effect on the mechanical properties. All materials were processed in a hot pressing process, and, subsequently, post-cured. The properties were characterized by the measurement of the swelling ratio, shore A-hardness, rebound resilience and tensile test. We successfully proved that ...
Aufsatz
Influence of ethylene oxide and gamma irradiation sterilization processes on the degradation behaviour of poly(lactic acid) (PLA) in the course of artificially accelerated aging
(2024-02-10)
To promote the application of bio-based materials in the field of medical technology, it is essential to conduct additional research, focusing on their long-term performance after sterilization. For this purpose, the study examines the aging behaviour of three poly(lactic-acid) (PLA) materials, sterilized with either ethylene oxide or gamma irradiation, over a two years aging period, in accordance with ASTM F1980-21. During these investigations, a direct correlation between moisture absorption and degradation progression ...
Aufsatz
In-situ full-field deformation analysis of injection-molded microcellular polycarbonate according to foam morphology patterns
(2023-06-02)
Deformation behavior of microcellular foam materials are sensitive to microstructural details. Therefore, the distinctive foam morphology patterns of foam injection-molded Polycarbonate are identified. These morphology patterns are investigated regarding their cell size, distance between cells, cell density, density reduction, homogeneity of cell size distribution, sphericity of cells and cell volume. Consequently, the predefined foam morphologies, the resulting modulus of elasticity and the elongation at break are ...
Aufsatz
Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
(2022-03-08)
This publication investigates the adhesion between an injection molded component and a self-reinforced composite (SRC) produced in a combined compaction and back-injection process to produce back-injected self-reinforced composites. To study the influence of the process, the parameters barrel temperature, time of injection, and tool temperature were varied. In addition, samples were taken at different positions along the flow path. In light of the orthotropic material behavior of SRCs, investigations were conducted ...
Aufsatz
Climatic Ageing of Components of Polymer Based Electrochromic Devices
(2013-09-09)
Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity ...
Aufsatz
Holzdesign trifft Kunststofftechnik
(2022)
Werkstoffverbunde aus Holzgeweben in einer thermoplastischen Matrix verbinden die Idee des textilen Holzbaus mit der Faserverbundtechnologie. In einem Projekt werden Fassadenelemente aus solchen Wood Textile Composites hergestellt. Dabei spielt neben den mechanischen Anforderungen auch die gestalterische Seite und die Akzeptanz der zukünftigen Nutzer eine wichtige Rolle.
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
Investigation of residual stresses in polypropylene using hot plate welding
(2020-08-05)
During the cooling process of the molten material, residual stresses appear because the reduced volume of the cooled material cannot fully fill the space formerly occupied by the molten material. The morphology in and around the weld is formed by different factors depending on the material and process parameters. Different morphological structures relate to different mechanical properties. The process parameters and the welding results including morphology and residual stress are linked together. In this article, ...
Aufsatz
Influence of the degree of crystallinity and the surface free energy on the adhesion properties of different PLA/PBS blends in multicomponent injection molding
(2020-01-10)
Biocomposites made of biodegradable polymers have grown in interest due to their environmentally friendliness, considering that non-biodegradable polymers waste conduces to pollution, displaying high environmental impact in climatic changes. Therefore, in the presented study, biodegradable Poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) were investigated as a series of PLA/PBS melt-blending compounds with the weight ratios of 50/50, 60/40, 70/30, 80/20 and 90/10. In a two-component injection molding ...
Aufsatz
Relaxation properties of polyoxymethylene and ethylene–octene copolymer blend in solid and melt states
(2012-08-30)
Rheological properties of polyoxymethylene (POM) and ethylene–octene copolymer (EOC) in solid and melt states were investigated. Blends were prepared with a twin screw extruder at broad component wt-to-wt ratios (10, 30, 50, 70, 90 wt% of EOC). The morphology as well as calorimetric, rheological, and elastic properties of the blends were studied. The investigation showed that POM/EOC blends were heterogeneous in nature and had a broad phase transition region between 30 and 70 wt% of POM. Because during processing ...