Search
Now showing items 61-70 of 81
Aufsatz
Holzdesign trifft Kunststofftechnik
(2022)
Werkstoffverbunde aus Holzgeweben in einer thermoplastischen Matrix verbinden die Idee des textilen Holzbaus mit der Faserverbundtechnologie. In einem Projekt werden Fassadenelemente aus solchen Wood Textile Composites hergestellt. Dabei spielt neben den mechanischen Anforderungen auch die gestalterische Seite und die Akzeptanz der zukünftigen Nutzer eine wichtige Rolle.
Aufsatz
Characterization of Anisotropic Properties of Hot Compacted Self-Reinforced Composites (SRCs) via Thermal Diffusivity Measurement
(2019-11-01)
The mechanical properties of self-reinforced composites (SRCs) produced in a hot compaction process significantly depend on the process parameters. Only a little deviation of the process temperature or pressure causes the component to act differently under mechanical load. This is a chance and a challenge at the same time, since this process is difficult to handle but by properly controlling the process parameters, the mechanical properties can be adjusted, even locally for one component. In this research SRC are ...
Aufsatz
Joining of Contact Pins and Conductive Compounds via Injection Molding – Influence of the Flow Situation on the Electrical Contact Resistance
(2020-04-09)
While a lot of research can be found in the field of bulk resistance of carbon filled polymers, comparatively few papers focus on contact resistance between compound and metal contacts. Due to that small number of researches that deal with contact resistances, studies of the influence of injection molding conditions and parameters on the contact resistance are also very rare. In contradiction to that, these influences on bulk resistance have been studied. The objective of this work was to investigate the electrical ...
Aufsatz
A Closer Look at the Bonding Capacity of Thick Metal-Plastic Hybrids
(2019-03-01)
Metal-plastic hybrids have a lot of advantages compared to purely metal or purely plastic parts. A good design for metal-plastic hybrids can help to save weight, for example in automotive applications. Therefore, it is important to understand the joining mechanisms between both materials. Aluminum AlSi9Cu3(Fe) and polyamide 6.6 with 35 % glass fibers were used as joining partners. The materials were joined by enclosing the metal part at least partially with plastic right inside the injection molding tool. Afterwards, ...
Aufsatz
UV Pre-Treatment for Polycarbonate for Bonding LSR in a Multi-Component Injection Molding Process
(2019-03-01)
In this study, the influence of UVC radiation and the influence of ozone on the surface energy of specimens made of polycarbonate were investigated. In an additional step, the peeling resistance of silicone flaps, which were overmolded, onto pre-treated PC plates of multicomponent specimens were analyzed. For this purpose, the samples were exposed to UVC radiation for different lengths of time, ranging from 5 s to 3 600 s. To further evaluate the influence of the ozone created by the UVC in the presence of oxygen, ...
Aufsatz
Investigations on Tightness of Polymer-Metal Hybrids in Environments with Thermal, Media, and Mechanical Loads
(2017-07-31)
With polymer-metal hybrids becoming more commonly used as structural components it was investigated how they perform in complex environments with combined thermal, media, and mechanical loads. Special attention was put on media tightness under said loads. This paper sums up the activities of the polymer technology research group of the University of Kassel on hybrids produced by overmolding metal inserts. Investigations concerning joint strength and influence of (cyclic) temperature loads and chemical corrosion on ...
Aufsatz
Mechanical Properties of Polydimethylsiloxane as a Function of the Amount and Type of Crosslinking Agent
(2017-06-13)
In this investigation, a high-consistency rubber (HCR) was mixed with five different, typically used crosslinking agents that are based on organic peroxide. Furthermore, the amount of crosslinking agent was varied in order to quantify the effect on the mechanical properties. All materials were processed in a hot pressing process, and, subsequently, post-cured. The properties were characterized by the measurement of the swelling ratio, shore A-hardness, rebound resilience and tensile test. We successfully proved that ...
Aufsatz
Influence of ethylene oxide and gamma irradiation sterilization processes on the degradation behaviour of poly(lactic acid) (PLA) in the course of artificially accelerated aging
(2024-02-10)
To promote the application of bio-based materials in the field of medical technology, it is essential to conduct additional research, focusing on their long-term performance after sterilization. For this purpose, the study examines the aging behaviour of three poly(lactic-acid) (PLA) materials, sterilized with either ethylene oxide or gamma irradiation, over a two years aging period, in accordance with ASTM F1980-21. During these investigations, a direct correlation between moisture absorption and degradation progression ...
Aufsatz
Characterization of polyamide 6.10 composites incorporated with microcrystalline cellulose fiber: Effects of fiber loading and impact modifier
(2018-08-14)
Microcrystalline cellulose (MCC) fiber‐reinforced polyamide 6.10 (PA) composites were prepared in the presence of an impact modifier (IM), exxelor VA1803 (VA), by melt compounding process. Fiber loading was considered from 20 to 30 wt.%, whereas IM was varied from 2.0 to 5.0 wt.%. Composites were characterized by tensile test, impact test, dynamic thermal mechanical analysis (DTMA), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and X‐ray diffraction (XRD). Composites’ fractured surfaces ...
Konferenzveröffentlichung
Influence Of The Fiber-Matrix-Interaction On The Fracture Behavior Of Regenerated Cellulose Fiber Reinforced Polypropylene
(Society of Plastics Engineers, 2017)
This investigation focuses on the fiber-matrix-interaction of man-made cellulose fibers (RCF) in a PP matrix with an additional MAPP content using an energetic evaluation of the single fiber pull-out test (SFPT). Furthermore glass fibers were characterized for reference purposes. With the SFPT the interfacial shear strength (IFFS) and the critical fiber length (lc) as well as the consumed energy of a fiber pull-out and a fiber rupture were determined. In a following step the resulting values of lc were related to the ...