Suche
Anzeige der Dokumente 1-10 von 71
Aufsatz
Tailoring flow behavior and heat transfer in tempering channels for high-pressure die casting—analysis of potentials of commercial static mixers and prospects of additive manufacturing
(2023-02-16)
Additive manufacturing (AM) opens up manifold possibilities to influence the heat transfer between fluid and die in high-pressure die casting (HPDC), eventually allowing to minimize the total cycle time of the process. AM already has been exploited to establish near-contour temperature control systems in industrial applications. However, AM not only allows to influence the position of tempering channels in dies but it also allows to influence the fluid dynamics itself, e.g., by imprinted static mixers. Up to now, ...
Aufsatz
Weathering of a Polyurethane-Based Gel Electrolyte
(2023-03-14)
A recently described flexible polyurethane electrolyte was artificially weathered at 25/50 °C and 50% r.h. in air and at 25 °C in a dry nitrogen atmosphere, each with and without UV irradiation. Different formulations and the polymer matrix, used as a reference, were weathered in order to investigate the influence of the amount of conductive lithium salt and the solvent propylene carbonate. The complete loss of the solvent at a standard climate was already observed after a few days, strongly influencing the ...
Aufsatz
Study of Dynamics in Metallic MEMS Cantilevers - Pull-In Voltage and Actuation Speed
(2023-01-13)
For different metals and varying geometries, this paper presents simulations of electrostatically actuated MEMS cantilevers regarding their influence on pull-in voltage and actuation speed. Three-dimensional electromechanical modeling including many non-linearities has been performed to study some static but mainly dynamic features. The results show that the involved parameters have different influences on the actuation speed and pull-in voltage: lower length, higher thickness as well as lower density and higher ...
Aufsatz
Potential of Fe-Mn-Al-Ni Shape Memory Alloys for Internal Prestressing of Ultra-High Performance Concrete
(2023-05-18)
Prestressing of concrete is a commonly used technique in civil engineering to achieve long spans, reduced structural thicknesses, and resource savings. However, in terms of application, complex tensioning devices are necessary, and prestress losses due to shrinkage and creep of the concrete are unfavourable in terms of sustainability. In this work, a prestressing method using novel Fe-Mn-Al-Ni shape memory alloy rebars as a tensioning system in UHPC is investigated. A generated stress of about 130 MPa was measured ...
Aufsatz
On the Monotonic and Cyclic Behavior of an Al-Mg-Zn-Cu-Si Compositionally Complex Alloy
(2023-08-03)
In present work, the monotonic and cyclic properties of a novel Al-Mg-Zn-Cu-Si compositionally complex alloy (CCA) are investigated. Microstructural studies reveal that a eutectic phase and fishbone-type structures are embedded in the Al-matrix. The mechanical properties of this CCA obtained under compressive loading are found to be promising. However, low ultimate strength and brittle behavior are seen under tension. The fatigue performance of the alloy in the low-cycle fatigue (LCF) regime is poor. Microstructural ...
Aufsatz
Hot Sheet Metal Forming Strategies for High-Strength Aluminum Alloys: A Review—Fundamentals and Applications
(2023-05-17)
In the past decade, aluminum alloys have become important structural materials in the automotive industry, thanks to their low density, high strength, high fracture toughness, and good fatigue performance. However, an important limitation of aluminum alloys is their poor formability at room temperature; as a result, numerous studies have been conducted with the aim of developing forming techniques to overcome this and facilitate the forming of more complex-shaped components. Following an overview on the metallurgical ...
Aufsatz
Additive Manufacturing of Binary Ni–Ti Shape Memory Alloys Using Electron Beam Powder Bed Fusion: Functional Reversibility Through Minor Alloy Modification and Carbide Formation
(2022-11-30)
Shape memory alloys (SMAs), such as Ni–Ti, are promising candidates for actuation and damping applications. Although processing of Ni–Ti bulk materials is challenging, well-established processing routes (i.e. casting, forging, wire drawing, laser cutting) enabled application in several niche applications, e.g. in the medical sector. Additive manufacturing, also referred to as 4D-printing in this case, is known to be highly interesting for the fabrication of SMAs in order to produce near-net-shaped actuators and ...
Aufsatz
On the Reliability of Automated Analysis of Fracture Surfaces Using a Novel Computer Vision-Based Tool
(2023-08-05)
Fracture surface analysis is of utmost importance with respect to structural integrity of metallic materials. This especially holds true for additively manufactured materials. Despite an increasing trend of automatization of testing methods, the analysis and classification of fatigue fracture surface images is commonly done manually by experts. Although this leads to correct results in most cases, it has several disadvantages, e.g., the need of a huge knowledge base to interpret images correctly. In present work, an ...
Aufsatz
Cyclic Superelastic Behavior of Iron-Based Fe-Ni-Co-Al-Ti-Nb Shape Memory Alloy
(2023-01-03)
Iron-based shape memory alloys came into focus as promising candidate materials for large-scale structural applications owing to their cost-efficiency. In the present work, the superelastic properties of a recently introduced Fe-Ni-Co-Al-Ti-Nb shape memory alloy are investigated. For 〈001〉-oriented single-crystalline material in aged condition (650 °C/6 h), an incremental strain test reveals excellent superelasticity at −130 °C with fully reversible strains up to about 6%. Under cycling loading at different test ...
Aufsatz
Electrochemical polarization behavior and superelastic properties of a Fe–Mn–Al–Ni–Cr shape memory alloy
(2022-10-22)
The present study investigates the corrosion behavior of a Fe–Mn–Al–Ni–Cr shape memory alloy in a 5.0 wt% NaCl solution in combination with the functional properties. In a single crystalline condition, the investigated alloy shows a superior superelastic response with a maximum recovery strain of 5.2%. Furthermore, the results of the potentiodynamic polarization and impedance spectroscopy show that the addition of chromium generally improves corrosion resistance by increasing the resistance to localized corrosion. ...