Suche
Anzeige der Dokumente 31-40 von 65
Aufsatz
Influence of Mean Stress on Lifetime Prediction of Adhesive Bonds
(2023-05-31)
The importance of adhesive bonds in the field of joining technology is increasing due to their advantageous properties. One of these attributes is the possibility to reduce the weight compared to welded joints in group of components. For a safe design, the knowledge of the lifetime of these components is essential. Various methods are used for the prediction of the lifetime under cyclic loading. On the one hand there are test-based methods, on the other hand simulation-based approaches. Test-based ones are often ...
Aufsatz
A Stability Analysis of Modified Patankar–Runge–Kutta methods for a nonlinear Production–Destruction System
(2023-03-24)
Modified Patankar–Runge–Kutta (MPRK) methods preserve the positivity as well as conservativity of a production–destruction system (PDS) of ordinary differential equations for all time step sizes. As a result, higher order MPRK schemes do not belong to the class of general linear methods, i. e. the iterates are generated by a nonlinear map g even when the PDS is linear. Moreover, due to the conservativity of the method, the map g possesses non-hyperbolic fixed points.
Recently, a new theorem for the investigation of ...
Aufsatz
Hybrid modeling of viscoelastic and switching–induced heating in ferroelectrics
(2023-03-24)
This contribution focuses on two effects causing a temperature change in electrically loaded ferroelectrics. These materials are often subjected to cyclic loading, where viscoelasticity prevails at lower electric fields, whereas dissipative heating by domain switching dominates above the coercive field. While viscoelasticity is modeled within a phenomenological, rheological framework, the ferroelectric constitutive behaviour is described based on a microphysical model. Merging both approaches results in the hybrid ...
Aufsatz
Benzene Oxidation over Pt Loaded on Fly Ash Zeolite X
(2023-07-20)
In the present study, zeolite X (FANaX) was synthesized from coal fly ash (FA) by a two-step high-temperature method. In order to follow the effect of different contaminants in the starting coal ash, zeolite X was also synthesized from pure chemicals according to a classical recipe (NaX). Iron was loaded on this reference zeolite with the amount which was contained in the coal FA. The final catalytic samples were obtained by wet impregnation of Pt nanoparticles on both types of zeolite crystals. The most active samples ...
Aufsatz
Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys
(2021-07-26)
In situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is ...
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
On the Monotonic and Cyclic Behavior of an Al-Mg-Zn-Cu-Si Compositionally Complex Alloy
(2023-08-03)
In present work, the monotonic and cyclic properties of a novel Al-Mg-Zn-Cu-Si compositionally complex alloy (CCA) are investigated. Microstructural studies reveal that a eutectic phase and fishbone-type structures are embedded in the Al-matrix. The mechanical properties of this CCA obtained under compressive loading are found to be promising. However, low ultimate strength and brittle behavior are seen under tension. The fatigue performance of the alloy in the low-cycle fatigue (LCF) regime is poor. Microstructural ...
Aufsatz
Liquid Silicone Rubber Foams Made with Water as Blowing Agent
(2021-08-18)
Liquid silicone rubber (LSR) is primarily used in injection molding. Foamed molded parts made of LSR are almost nonexistent because the process reliability of LSR foam injection molding is currently not given. It makes sense to have suitable foaming processes for this material as well, because the density of this elastomer is about 1.15 g cm−3. With the injection molding process presented herein for foaming LSR, density reductions of up to 40% can be achieved. In this process, up to 3% by weight of water is added to ...
Aufsatz
Hot Sheet Metal Forming Strategies for High-Strength Aluminum Alloys: A Review—Fundamentals and Applications
(2023-05-17)
In the past decade, aluminum alloys have become important structural materials in the automotive industry, thanks to their low density, high strength, high fracture toughness, and good fatigue performance. However, an important limitation of aluminum alloys is their poor formability at room temperature; as a result, numerous studies have been conducted with the aim of developing forming techniques to overcome this and facilitate the forming of more complex-shaped components. Following an overview on the metallurgical ...
Aufsatz
Additive Manufacturing of Binary Ni–Ti Shape Memory Alloys Using Electron Beam Powder Bed Fusion: Functional Reversibility Through Minor Alloy Modification and Carbide Formation
(2022-11-30)
Shape memory alloys (SMAs), such as Ni–Ti, are promising candidates for actuation and damping applications. Although processing of Ni–Ti bulk materials is challenging, well-established processing routes (i.e. casting, forging, wire drawing, laser cutting) enabled application in several niche applications, e.g. in the medical sector. Additive manufacturing, also referred to as 4D-printing in this case, is known to be highly interesting for the fabrication of SMAs in order to produce near-net-shaped actuators and ...