Suche
Anzeige der Dokumente 21-30 von 95
Aufsatz
A Novel Thermo-Mechanical Processing Route Exploiting Abnormal Grain Growth in Heusler-Type Co–Ni–Ga Shape Memory Alloys
(2022-10-04)
Heusler-type Co–Ni–Ga shape memory alloys attracted significant scientific attention owing to excellent superelasticity in single-crystalline state. However, due to pronounced anisotropy, polycrystalline Co–Ni–Ga suffers from transformation-induced constraints at grain boundaries and, thus, premature failure upon thermo-mechanical loading. The present study reports on a novel thermo-mechanical processing route. Hot rolling followed by solution-annealing promotes abnormal grain growth, eventually leading to high-performance ...
Aufsatz
Cooling rate as a process parameter in advanced roll forming to tailor microstructure,mechanical and corrosion properties of EN AW 7075 tubes
(2022-12-14)
The effects of solution heat treatment parameters and quench media as a processing tool for tailoring microstructure, mechanical and corrosion properties in roll forming of EN AW 7075 alloy were studied. The highest yield stress and ultimate tensile strength were obtained for the specimens quenched in water, while the air-cooled specimens exhibited inferior mechanical properties. Microstructural analysis of specimens showed that except water-quenched specimens, the parts cooled/quenched in oil, in direct contact with ...
Aufsatz
On the Friction Stir Processing of Additive-Manufactured 316L Stainless Steel
(2022)
The novel combination of friction stir processing (FSP) and additive manufacturing (AM) is studied herein. Laser-based powder bed fusion of metals (PBF-LB/M) is used to establish 316 L stainless steel with a bimodal microstructure. Upon FSP, the as-built bimodal microstructure with an average grain size of 179 μm is transformed into the unimodal microstructure containing ultrafine grains with an average grain size of 1.2 μm. Results obtained by mechanical testing reveal that after FSP; the hardness, the yield point, ...
Aufsatz
Oxide Modified Iron in Electron Beam Powder Bed Fusion - From Processability to Corrosion Properties
(2022-03-07)
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material composition, and the solidification behavior of the material considered. However, when complex specific requirements have to be met, a targeted part design is highly challenging. In the field of biodegradable implant surgery, a cytocompatible material of an application-adapted ...
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
Values as leverage points for sustainability transformation: two pathways for transformation research
(2022-08-13)
The burgeoning literature on sustainability transformation agrees that values play a key, albeit unelucidated, role on the transformation research agenda. Recent literature linking values and transformation increasingly points toward the hypothesis that values may act as leverage points for sustainability transformation. However, how transformation research can engage with values as leverage points remains a critical knowledge gap. Here, I argue that transformation research needs to distinguish between two modes of ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...
Aufsatz
Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
(2022-03-03)
In this research paper, the effects of the combined compacting and back-injection process to produce back-injected self-reinforced composites on the mechanical properties of the self-reinforced composites (SRCs) are investigated. For this purpose, the parameters barrel temperature, time of injection and holding pressure were varied for the back injection. Tensile and bending tests were carried out on the SRCs. The results show that the mechanical properties depend to a large extent on the process parameters. The ...
Aufsatz
Circular bioeconomy: Actors and dynamics of knowledge co-production in Finland
(2022-09-01)
The circular bioeconomy is a highly scrutinized concept in Finland and internationally, with a high degree of polarization regarding forest utilization rates and distrust between certain actors. This offers an interesting case for an exploratory analysis of issues associated with knowledge co-production. Knowledge co-production entails the integration of different knowledge types and collaboration across multiple societal actors with potentially conflicting viewpoints and agendas. We interviewed key organizations ...
Aufsatz
Effects of aging on the stress-induced martensitic transformation and cyclic superelastic properties in Co-Ni-Ga shape memory alloy single crystals under compression
(2022)
Co-Ni-Ga shape memory alloys attracted scientific attention as promising candidate materials for damping applications at elevated temperatures, owing to excellent superelastic properties featuring a fully reversible stress-strain response up to temperatures as high as 500 °C. In the present work, the effect of aging treatments conducted in a wide range of aging temperatures and times, i.e. at 300–400 °C for 0.25–8.5 h, was investigated. It is shown that critical features of the martensitic transformation are strongly ...