Suche
Anzeige der Dokumente 61-70 von 1991
Aufsatz
Thermal Properties of Plasticized Cellulose Acetate and Its β-Relaxation Phenomenon
(2021-04-21)
Cellulose acetate (CA), an organic ester, is a biobased polymer which exhibits good mechanical properties (e.g., high Young’s modulus and tensile strength). In recent decades, there has been significant work done to verify the thermal and thermomechanical behaviors of raw and plasticized cellulose acetate. In this study, the thermomechanical properties of plasticized cellulose acetate—especially its β-relaxation and activation energy—were investigated. The general thermal behavior was analyzed and compared with ...
Aufsatz
Observation of two-electron-one-photon transitions in silicon
(1977)
We report on the observation of K\alpha\alpha X-rays of Si, produced in collisions of 15-28 MeV Si projectiles with various target atoms in the range Z =6 to 29. Energy shifts of X-rays were measured and are compared with theoretical predictions. Cross section ratios for emission of K\alpha\alpha and K\alpha radiation are given.
Aufsatz
Story Analyzing als Zugang zur Organisationskultur
(2006)
The Psychohistory of Lloyd deMause as a key to corporate culture - The corporate culture approach is considered a central key to the understanding of the dynamics of organizations. Since the corporate culture mirrors unconscious contexts of meaning, culture analysis in organizations gain in importance. Narratives convey culture. So why not use narratives for the analysis of organisational cultures? The combination of data collection through work biographies with a resembling »narrative analytical method« such as the ...
Aufsatz
Relativistic ab initio calculations for ion-atom collisions
(Richard, Patrick (Hrsg.), 1993)
Within the independent particle model we solve the time-dependent single-particle equation using ab initio SCF-DIRAC-FOCK-SLATER wavefunctions as a basis. To reinstate the many-particle aspect of the collision system we use the inclusive probability formalism to answer experimental questions. As an example we show an application to the case of S{^15+} on Ar where experimental data on the K-K charge transfer are available for a wide range of impact energies from 4.7 to 90 MeV. Our molecular adiabatic calculations and ...
Aufsatz
Mittelalter erschließen
(2021-07-15)
Research communication has been gaining public attention in recent years. Therefore, medievalists also need to focus on the transfer of their research topics to the public both within and outside the university. Based on current political demands calling for a change in communication culture, the article first of all deals theoretically with two different concepts of research communication, by distinguishing between forms of translation and those of popularization. Numerous public events, exhibitions, and cooperative ...
Aufsatz
On the Monotonic and Cyclic Behavior of an Al-Mg-Zn-Cu-Si Compositionally Complex Alloy
(2023-08-03)
In present work, the monotonic and cyclic properties of a novel Al-Mg-Zn-Cu-Si compositionally complex alloy (CCA) are investigated. Microstructural studies reveal that a eutectic phase and fishbone-type structures are embedded in the Al-matrix. The mechanical properties of this CCA obtained under compressive loading are found to be promising. However, low ultimate strength and brittle behavior are seen under tension. The fatigue performance of the alloy in the low-cycle fatigue (LCF) regime is poor. Microstructural ...
Aufsatz
Hot Sheet Metal Forming Strategies for High-Strength Aluminum Alloys: A Review—Fundamentals and Applications
(2023-05-17)
In the past decade, aluminum alloys have become important structural materials in the automotive industry, thanks to their low density, high strength, high fracture toughness, and good fatigue performance. However, an important limitation of aluminum alloys is their poor formability at room temperature; as a result, numerous studies have been conducted with the aim of developing forming techniques to overcome this and facilitate the forming of more complex-shaped components. Following an overview on the metallurgical ...
Aufsatz
Experimental Analysis of the Stability of Retained Austenite in a Low-Alloy 42CrSi Steel after Different Quenching and Partitioning Heat Treatments
(2023-06-21)
Quenching and partitioning (Q&P) steels are characterized by an excellent combination of strength and ductility, opening up great potentials for advanced lightweight components. The Q&P treatment results in microstructures with a martensitic matrix being responsible for increased strength whereas interstitially enriched metastable retained austenite (RA) contributes to excellent ductility. Herein, a comprehensive experimental characterization of microstructure evolution and austenite stability is carried out on a ...
Aufsatz
Microstructural and mechanical properties of AlSi10Mg: Hybrid welding of additively manufactured and cast parts
(2022-12-07)
Welding and joining of hybrid components consisting of additively manufactured (AM) parts and conventionally processed parts offer new opportunities in structural design. In the present study, AlSi10Mg specimens were fabricated using two different manufacturing processes, i.e., laser-based powder-bed fusion of metals (PBF-LB/M) and casting, and welded by means of friction stir welding (FSW). Material strength of dissimilar welded joints was found to be governed by the as-cast material, which is characterized by a ...