Search
Now showing items 31-40 of 158
Dissertation
Gasleckortungsmethoden für autonome mobile Inspektionsroboter mit optischer Gasfernmesstechnik in industrieller Umgebung
(Kassel Univ. Press, 2015)
In vielen Industrieanlagen werden verschiedenste Fluide in der Produktion eingesetzt, die bei einer Freisetzung, z. B. durch ihre toxische oder karzinogene Eigenschaft oder wegen der Brand- und Explosionsgefahr, sowohl die Umwelt als auch Investitionsgüter gefährden können. In Deutschland sind zur Risikominimierung die maximal zulässigen Emissionsmengen von Stoffen und Stoffgruppen in verschiedenen Umweltvorschriften festgelegt, wodurch zu deren Einhaltung eine ausreichende Überwachung aller relevanten Anlagenkomponenten ...
Dissertation
Experimentelle Modalanalyse und aktive Schwingungsdämpfung eines biegeelastischen Rotors
(kassel university press, 2011)
Die vorliegende Dissertation leistet einen Beitrag zur experimentellen Modalanalyse und aktiven Schwingungsdämpfung biegeelastischer Rotoren. Die experimentelle Modalanalyse ist ein gängiges Verfahren zur Identifikation modaler Parameter in der Maschinen- und Strukturdynamik. Ebenso gilt dies für die aktive Schwingungsdämpfung, wobei hier die Entwicklung zuverlässiger Applikationen noch deutlich im Fluss ist. In beiden Fällen stellen Anwendungen in der Rotordynamik besondere Anforderungen dar. Die Einleitung der ...
Dissertation
Co-Simulation und Solverkopplung
(kassel university press, 2015)
In dieser Dissertation werden zwei Arten von gekoppelter Simulation anhand einfacher Testmodelle untersucht und auf komplexe, multiphysikalische Systeme angewandt. Dazu werden die Gesamtsysteme in monodisziplinäre Subsysteme aufgeteilt. Die Modellierung der Subsysteme erfolgt mithilfe kommerzieller Programme. Für die Simulation werden die in den Programmen integrierten Gleichungslöser eingesetzt. In den komplexen Anwendungen wird in dieser Arbeit immer ein Mehrkörpersystem (MKS) mit einem oder mehreren Modellen aus ...
Aufsatz
Promoting abnormal grain growth in Fe-based shape memory alloys through compositional adjustments
(2019-05-28)
Iron-based shape memory alloys are promising candidates for large-scale structural applications due to their cost efficiency and the possibility of using conventional processing routes from the steel industry. However, recently developed alloy systems like Fe–Mn–Al–Ni suffer from low recoverability if the grains do not completely cover the sample cross-section. To overcome this issue, here we show that small amounts of titanium added to Fe–Mn–Al–Ni significantly enhance abnormal grain growth due to a considerable ...
Dissertation
Zweiskalensimulation von mikroheterogenen Strukturen aus spröden Faserverbundwerkstoffen
(Kassel Univ. Press, 2010)
Die vorliegende Dissertation behandelt die Zweiskalensimulation von mikroheterogenen Faserverbundwerkstoffstrukturen. Die Berechnung von Bauteilen aus inhomogenen Werkstoffen wird als Mehrskalenaufgabe betrachtet. Im Gegensatz zum Stand der Technik, der im Allgemeinen von der Betrachtungsweise des Werkstoff als homogenes Kontinuum ausgeht, berücksichtigt der in dieser Arbeit verfolgte, methodische Ansatz den inhomogenen Materialaufbau aus verschiedenen Werkstoffphasen. Die Auslegung von Faserverbundbauteilen hinsichtlich ...
Aufsatz
Cyclic degradation of Co49Ni21Ga30 high-temperature shape memory alloy - On the roles of dislocation activity and chemical order
(2015)
Conventional shape memory alloys (SMAs), such as binary Ni-Ti, are typically limited to service temperatures below 100 °C. Recent studies on Co-Ni-Ga high temperature (HT) SMAs revealed the potential that these alloys can be used up to temperatures of about 400 °C. Analysis of the cyclic functional properties showed that degradation in these alloys is mainly triggered by intensive dislocation motion. However, data on the cyclic stress-strain response and the mechanisms leading to functional degradation of Co-Ni-Ga ...
Aufsatz
Bend Straightening of a Carbonitrided Gear Shaft – Consequences on Residual Stresses and Retained Austenite near the Surface
(2017-06-20)
Carbonitriding of shafts in drive technology is strongly connected with distortion. Bend straightening is an important process step in order to eliminate distortion without removing the hardened surface layer. As shown in several investigations, even for simple part geometries, bending induced stresses and plastic deformations have a strong impact not only on the residual stress state but also on the microstructure after straightening. As gear shafts become increasingly filigree and complex in their geometry, the ...
Aufsatz
Climatic Ageing of Components of Polymer Based Electrochromic Devices
(2013-09-09)
Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity ...
Aufsatz
UV Surface Treatment of Polycarbonate for Adhesion Improvement to Liquid Silicone Rubber (LSR)
(2018)
The adhesion of self-adhesive liquid silicone rubbers to thermoplasts is only possible for a few selected material combinations without a surface pretreatment. A UV pretreatment is effective for polycarbonate and short irradiation periods are sufficient. To clarify the required irradiation conditions that result in an improvement of adhesion, the varying irradiation conditions were assessed. FTIR-ATR spectroscopy was used for surface analysis to characterize the change in the polymer surface.