Suche
Anzeige der Dokumente 51-60 von 127
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
High Consistency Silicone Rubber Foams
(2024-04-23)
Silicone elastomers are high-performance plastics. In the extrusion process, only high-consistency silicone rubbers were used. In order to reduce the cost and weight, silicone rubbers can be foamed during processing. In this study, high-consistency silicone rubber is processed with different physical and chemical blowing agents. The resulting reaction kinetics, as well as the mechanical and morphological properties, had been investigated and compared with each other. This showed that the chemical blowing agent ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...
Aufsatz
Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
(2022-03-03)
In this research paper, the effects of the combined compacting and back-injection process to produce back-injected self-reinforced composites on the mechanical properties of the self-reinforced composites (SRCs) are investigated. For this purpose, the parameters barrel temperature, time of injection and holding pressure were varied for the back injection. Tensile and bending tests were carried out on the SRCs. The results show that the mechanical properties depend to a large extent on the process parameters. The ...
Aufsatz
Joining of Contact Pins and Conductive Compounds via Injection Molding – Influence of the Flow Situation on the Electrical Contact Resistance
(2020-04-09)
While a lot of research can be found in the field of bulk resistance of carbon filled polymers, comparatively few papers focus on contact resistance between compound and metal contacts. Due to that small number of researches that deal with contact resistances, studies of the influence of injection molding conditions and parameters on the contact resistance are also very rare. In contradiction to that, these influences on bulk resistance have been studied. The objective of this work was to investigate the electrical ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Effects of aging on the stress-induced martensitic transformation and cyclic superelastic properties in Co-Ni-Ga shape memory alloy single crystals under compression
(2022)
Co-Ni-Ga shape memory alloys attracted scientific attention as promising candidate materials for damping applications at elevated temperatures, owing to excellent superelastic properties featuring a fully reversible stress-strain response up to temperatures as high as 500 °C. In the present work, the effect of aging treatments conducted in a wide range of aging temperatures and times, i.e. at 300–400 °C for 0.25–8.5 h, was investigated. It is shown that critical features of the martensitic transformation are strongly ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Microstructure of an additively manufactured Ti-Ta-Al alloy using novel pre-alloyed powder feedstock material
(2023-05-01)
Binary Ti-Ta and ternary Ti-Ta-Al alloys attracted considerable attention as new potential biomaterials and/or high-temperature shape memory alloys. However, conventional forming and manufacturing technologies of refractory based titanium alloys are difficult and cost-intensive, especially when complex shapes are required. Recently, additive manufacturing (AM) emerged as a suitable alternative and several studies exploited elemental powder mixing approaches to obtain a desired alloy and subsequently use it for complex ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Influence of ethylene oxide and gamma irradiation sterilization processes on the degradation behaviour of poly(lactic acid) (PLA) in the course of artificially accelerated aging
(2024-02-10)
To promote the application of bio-based materials in the field of medical technology, it is essential to conduct additional research, focusing on their long-term performance after sterilization. For this purpose, the study examines the aging behaviour of three poly(lactic-acid) (PLA) materials, sterilized with either ethylene oxide or gamma irradiation, over a two years aging period, in accordance with ASTM F1980-21. During these investigations, a direct correlation between moisture absorption and degradation progression ...
Dissertation
Bewertung von Eigenspannungen nach dem Laserstrahlhärten von komplex geformten Komponenten und additiv gefertigten Bauteilen
(2021)
Die Laserstrahlbearbeitung hat sich im Laufe der letzten Jahre zu einem wichtigen Forschungsschwerpunkt in industrieller und akademischer Hinsicht entwickelt. Neben der Erschließung neuer Anwendungsgebiete durch den Vorteil einer hohen Bearbeitungsflexibilität überzeugt die laserbasierte Materialbearbeitung vor allem durch einen lokal beeinflussbaren Energieeintrag. Jedoch sind derzeit mit zunehmender geometrischer Komplexität und Bauteilgröße nur begrenzte Tiefenwirkungen der gewünschten Druckeigenspannungen ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys
(2021-07-26)
In situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
In-situ full-field deformation analysis of injection-molded microcellular polycarbonate according to foam morphology patterns
(2023-06-02)
Deformation behavior of microcellular foam materials are sensitive to microstructural details. Therefore, the distinctive foam morphology patterns of foam injection-molded Polycarbonate are identified. These morphology patterns are investigated regarding their cell size, distance between cells, cell density, density reduction, homogeneity of cell size distribution, sphericity of cells and cell volume. Consequently, the predefined foam morphologies, the resulting modulus of elasticity and the elongation at break are ...