Search
Now showing items 211-220 of 401
Aufsatz
Constant Temperature Approach for the Assessment of Injection Molding Parameter Influence on the Fatigue Behavior of Short Glass Fiber Reinforced Polyamide 6
(2021-05-13)
Short glass fiber reinforced plastics (SGFRP) offer superior mechanical properties compared to polymers, while still also enabling almost unlimited geometric variations of components at large-scale production. PA6-GF30 represents one of the most used SGFRP for series components, but the impact of injection molding process parameters on the fatigue properties is still insufficiently investigated. In this study, various injection molding parameter configurations were investigated on PA6-GF30. To take the significant ...
Aufsatz
Innovative Materials for Novel Concepts for Internal Heat Exchangers
(2018-07-27)
Internal heat exchangers are often employed in solar thermal applications as well as in many other applications that involve heat, and, for the most part, consist of metallic materials (copper, stainless steel). Corrugated stainless steel tubes are easy to assemble, and are commonly used in various storage geometries. In order to significantly reduce costs, alternative materials, such as plastics, can function as excellent substitutes. Alternative heat exchangers for the following examinations using various materials ...
Aufsatz
Thermal Properties of Plasticized Cellulose Acetate and Its β-Relaxation Phenomenon
(2021-04-21)
Cellulose acetate (CA), an organic ester, is a biobased polymer which exhibits good mechanical properties (e.g., high Young’s modulus and tensile strength). In recent decades, there has been significant work done to verify the thermal and thermomechanical behaviors of raw and plasticized cellulose acetate. In this study, the thermomechanical properties of plasticized cellulose acetate—especially its β-relaxation and activation energy—were investigated. The general thermal behavior was analyzed and compared with ...
Dissertation
Konzept und Prototyp eines interoperablen und offenen Simulationssystems
(2008-10-20)
Simulation hat sich in der Vergangenheit als unterstützendes Planungsinstrument und Prognosemethode zur Untersuchung von Materialflusssystemen in verschiedenen Branchen etabliert. Dafür werden neben Simulationswerkzeugen auch zunehmend Virtual Reality (VR), insbesondere mit dem Ansatz Digitale Fabrik, eingesetzt. Ein Materialflusssimulator, der für den VR–Einsatz geeignet ist,existiert noch nicht, so dass Anwender gegenwärtig mit verschiedenen Systemen arbeiten müssen, um Untersuchungen eines Simulationsmodells in ...
Dissertation
Sensordatenfusionsansätze in der Thermografie zur Verbesserung der Messergebnisse
(kassel university presskassel university press, 2014)
Thermografie hat sich als wichtiges Hilfsmittel für die Inspektion, Prüfung und Überwachung etabliert. Bei vielen Anwendungen ist eine einzelne Messung allein oft nicht aussagekräftig, z. B. weil Strukturen nicht deutlich genug wahrgenommen werden können, das Messobjekt größer als das Blickfeld der Optik ist oder sich Kenngrößen erst aus dem zeitlichen Verlauf von Messungen ergeben. Zudem erfasst der Bediener der Kamera mit seinen Sinnen und seiner Erfahrung noch viele weitere Einflussgrößen, die bei der Entscheidungsfindung ...
Aufsatz
Shape Memory Effect and Superelasticity of [001]-Oriented FeNiCoAlNb Single Crystals Aged under and without Stress
(2021-06-10)
The two-step ageing of Fe-28Ni-17Co-11.5Al-2.5Nb (at.%) single crystals under and without stress, leads to the precipitation of the γ′- and β-phase particles. Research has shown that γ–α′ thermoelastic martensitic transformation (MT), with shape memory effect (SME) and superelasticity (SE), develops in the [001]-oriented crystals under tension. SE was observed within the range from the temperature of the start of MT upon cooling Mₛ, to the temperature of the end of the reverse MT upon heating Af, and at temperatures ...
Aufsatz
Experimental Analysis of Residual Stresses in CFRPs through Hole-Drilling Method: The Role of Stacking Sequence, Thickness, and Defects
(2023-05-09)
Carbon fiber reinforced plastics (CFRPs) gained high interest in industrial applications because of their excellent strength and low specific weight. The stacking sequence of the unidirectional plies forming a CFRP laminate, and their thicknesses, primarily determine the mechanical performance. However, during manufacturing, defects, e.g., pores and residual stresses, are induced, both affecting the mechanical properties. The objective of the present work is to accurately measure residual stresses in CFRPs as well ...
Aufsatz
Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures
(2022-08-13)
The unique microstructure of the alloy AlSi10Mg produced by the laser-based powder bed fusion of metals (PBF-LB/M) provides high-strength and high-strain-hardening capabilities of the material. The microstructure and mechanical properties of 3D-printed, i.e., additively manufactured, AlSi10Mg are significantly altered by post-building heat-treatment processes applied in order to tailor the final properties of the parts. Using an accurate computational model to predict and improve the mechanical performance of 3D-printed ...
Aufsatz
Influence of the Miniaturisation Effect on the Effective Stiffness of Lattice Structures in Additive Manufacturing
(2020-10-29)
Thin-walled and cellular structures are characterised by superior lightweight potential due to their advantageous stiffness to weight ratio. They find particular interest in the field of additive manufacturing due to robust and reproducible manufacturability. However, the mechanical performance of such structures strongly depends on the manufacturing process and resultant geometrical imperfections such as porosity, deviations in strut thickness or surface roughness, for which an understanding of their influence is ...
Aufsatz
The Effect of Fiber Waviness on the Residual Stress State and Its Prediction by the Hole Drilling Method in Fiber Metal Laminates: A Global-Local Finite Element Analysis
(2021-01-15)
In this paper, fiber waviness, as one of the most frequently occurring defects in fiber reinforced composites, is numerically investigated with regard to the formation of residual stresses in fiber metal laminates. Furthermore, the prediction of the residual stress state in the thickness direction by means of the simulated hole drilling method is studied. To this regard, a global-local finite element analysis based on the submodel technique is presented. The submodel technique essentially consists of two governing ...