Suche
Anzeige der Dokumente 31-40 von 46
Aufsatz
A Novel Thermo-Mechanical Processing Route Exploiting Abnormal Grain Growth in Heusler-Type Co–Ni–Ga Shape Memory Alloys
(2022-10-04)
Heusler-type Co–Ni–Ga shape memory alloys attracted significant scientific attention owing to excellent superelasticity in single-crystalline state. However, due to pronounced anisotropy, polycrystalline Co–Ni–Ga suffers from transformation-induced constraints at grain boundaries and, thus, premature failure upon thermo-mechanical loading. The present study reports on a novel thermo-mechanical processing route. Hot rolling followed by solution-annealing promotes abnormal grain growth, eventually leading to high-performance ...
Aufsatz
Hot Work Tool Steel Processed by Laser Powder Bed Fusion: A Review on Most Relevant Influencing Factors
(2021-03-26)
As a representative of a common carbon-bearing hot work tool steel AISI H13 is in focus of the present review paper. Most relevant details for processing of AISI H13 by laser powder bed fusion (L-PBF) are systematically investigated. Three common stages of process parameter development and material assessment, respectively, are in focus: general processibility, process refinement, and deduction of process–microstructure–property relations, i.e., understanding of the interplay of relevant elementary mechanisms. On the ...
Aufsatz
CuCrZr processed by laser powder bed fusion — Processability and influence of heat treatment on electrical conductivity, microstructure and mechanical properties
(2021-06-16)
CuCrZr parts were fabricated by laser beam powder bed fusion (LB-PBF) technique and subjected to different heat treatments. As a result, four different conditions were considered for further investigations, that is, the as-built condition, conditions of maximum hardness (MH) and maximum electrical conductivity (MC), and a condition representing a compromise between hardness and conductivity (H&C). Microstructural evolution and performance under monotonic and cyclic loading were studied. Fracture surfaces revealed ...
Aufsatz
On the Microstructural and Cyclic Mechanical Properties of Pure Iron Processed by Electron Beam Melting
(2021-03-10)
Additive manufacturing (AM) processes such as electron beam melting (EBM) are characterized by unprecedented design freedom. Topology optimization and design of the microstructure of metallic materials are enabled by rapid progress in this field. The latter is of highest importance as many applications demand appropriate mechanical as well as functional material properties. For instance, biodegradable implants have to meet mechanical properties of human bone and at the same time guarantee adequate cytocompatibility ...
Aufsatz
Thermal Stability of Residual Stresses in Differently Deep Rolled Surface Layers of Steel SAE 1045
(2021-05-07)
The stability of compressive residual stresses generated by deep rolling plays a decisive role on the fatigue behavior of specimens and components, respectively. In this regard, deep rolling at elevated temperature has proven to be very effective in stabilizing residual stresses when fatigue analysis is conducted at ambient temperature. However, since residual stresses can be affected not only by plastic deformation but also when thermal energy is provided, it is necessary to analyze the influence of temperature and ...
Aufsatz
Parameter recommendation for injection molding based on similarity analysis of injection molded parts
(2023)
Injection molding is a widespread manufacturing process for producing complex plastic shapes. The process is controlled by a large number of parameters, which show interactions with each other. Thereby the determination of an optimal operating point during sampling is a resource-consuming and demanding task. The data, which is generated during sampling, is usually not used for subsequent sampling processes. In the context of Industry 4.0, manufacturing companies attempt to optimize production efficiency to save time ...
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
High Consistency Silicone Rubber Foams
(2024-04-23)
Silicone elastomers are high-performance plastics. In the extrusion process, only high-consistency silicone rubbers were used. In order to reduce the cost and weight, silicone rubbers can be foamed during processing. In this study, high-consistency silicone rubber is processed with different physical and chemical blowing agents. The resulting reaction kinetics, as well as the mechanical and morphological properties, had been investigated and compared with each other. This showed that the chemical blowing agent ...
Aufsatz
Pathways toward the Use of Non-Destructive Micromagnetic Analysis for Porosity Assessment and Process Parameter Optimization in Additive Manufacturing of 42CrMo4 (AISI 4140)
(2024-02-20)
Laser-based powder bed fusion of metals (PBF-LB/M) is a widely applied additive manufacturing technique. Thus, PBF-LB/M represents a potential candidate for the processing of quenched and tempered (Q&T) steels such as 42CrMo4 (AISI 4140), as these steels are often considered as the material of choice for complex components, e.g., in the toolmaking industry. However, due to the presence of process-induced defects, achieving a high quality of the resulting parts remains challenging in PBF-LB/M. Therefore, an extensive ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...