Suche
Anzeige der Dokumente 31-40 von 78
Aufsatz
Cyclic degradation of Co49Ni21Ga30 high-temperature shape memory alloy - On the roles of dislocation activity and chemical order
(2015)
Conventional shape memory alloys (SMAs), such as binary Ni-Ti, are typically limited to service temperatures below 100 °C. Recent studies on Co-Ni-Ga high temperature (HT) SMAs revealed the potential that these alloys can be used up to temperatures of about 400 °C. Analysis of the cyclic functional properties showed that degradation in these alloys is mainly triggered by intensive dislocation motion. However, data on the cyclic stress-strain response and the mechanisms leading to functional degradation of Co-Ni-Ga ...
Aufsatz
Bend Straightening of a Carbonitrided Gear Shaft – Consequences on Residual Stresses and Retained Austenite near the Surface
(2017-06-20)
Carbonitriding of shafts in drive technology is strongly connected with distortion. Bend straightening is an important process step in order to eliminate distortion without removing the hardened surface layer. As shown in several investigations, even for simple part geometries, bending induced stresses and plastic deformations have a strong impact not only on the residual stress state but also on the microstructure after straightening. As gear shafts become increasingly filigree and complex in their geometry, the ...
Aufsatz
Climatic Ageing of Components of Polymer Based Electrochromic Devices
(2013-09-09)
Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Relaxation properties of polyoxymethylene and ethylene–octene copolymer blend in solid and melt states
(2012-08-30)
Rheological properties of polyoxymethylene (POM) and ethylene–octene copolymer (EOC) in solid and melt states were investigated. Blends were prepared with a twin screw extruder at broad component wt-to-wt ratios (10, 30, 50, 70, 90 wt% of EOC). The morphology as well as calorimetric, rheological, and elastic properties of the blends were studied. The investigation showed that POM/EOC blends were heterogeneous in nature and had a broad phase transition region between 30 and 70 wt% of POM. Because during processing ...
Aufsatz
Mechanical properties of hybrid glass/kenaf fibre-reinforced epoxy composite with matrix modification using liquid epoxidised natural rubber
(2015-04-27)
The hybridisation of natural fibre with glass fibre provides a method to improve the mechanical properties instead of using the natural fibres alone. This research is focused on the hybridisation of glass/kenaf fibre with the addition of liquid epoxidised natural rubber to enhance the desired mechanical properties of the composite by reducing the synthetic fibre usage and encourage the natural fibre consumption. Liquid epoxidised natural rubber was added to the epoxy matrix in order to improve its mechanical properties ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Parameter identification for constitutive models of innovative textile composite materials using digital image correlation
(2019-11-18)
This contribution focuses on an innovative composite material consisting of textile layers made from continuous wooden fibers embedded in a thermoplastic matrix. A finite element simulation of potential use‐cases is planned to support the development process and to study the suitability of the material in an architectural context. The simulation is based on a constitutive model assuming homogenous orthotropic elastic behavior and will be expanded to include multiscale modeling in future research. The material parameters ...
Aufsatz
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
A Comparison Study of Liquid Natural Rubber (LNR) and Liquid Epoxidized Natural Rubber (LENR) as the Toughening Agent for Epoxy
(2013)
Rubber-toughened epoxy resins were prepared using the mechanical stirring method and molded into samples by compression molding. The aim of this study is to modify the brittleness of the epoxy matrix by adding discrete rubbery phases to improve the toughness properties. Liquid natural rubber (LNR) and liquid epoxidized natural rubber (LENR) were used as toughening agents in the epoxy resin to compare the properties of the modified networks. The mechanical and thermal properties have been studied to observe the effect ...
Buch
![Open Access](/themes/Mirage2/images/Open_Access_logo_PLoS_transparent.svg)
Thermo-mechanische Gradierung eigenverstärkter Polypropylen-Composite
(kassel university press, 2015)
Eigenverstärkte Polypropylen-Composite weisen ein enormes Leichtbaupotential und überdurchschnittliche mechanische Grundeigenschaften auf. Das Eigenschaftsspektrum lässt sich auf die makromolekulare Orientierung oder sog. Eigenverstärkung der eingesetzten textilen Faser- und Bändchenhalbzeuge zurückführen, welche die Ausgangsbasis der Schichtverbunde bilden. Über eine gezielte Prozessführung kann die Eigenverstärkung bis ins heißkompaktierte Bauteil hinein kontrolliert und erhalten werden, wobei sich das Eigenschaftsspektrum ...
Aufsatz
Morphology-property-relationship of thermo-mechanically graded self-reinforced polypropylene composites
(2015-02-17)
In this paper the relationship between different composite morphologies and their mechanical properties is to be investigated. By manufacturing two different tape-based polypropylene composites in a compression moulding process, four varying degrees of compaction will be generated. The morphological structure is analyzed using confocal laser light microscopy and wet chemically etched specimen cross-sections. The etching process removes the amorphous phase in the polymer, making the macromolecular orientations and ...