Suche
Anzeige der Dokumente 71-80 von 100
Konferenzveröffentlichung
Changeable Thermal Management for LED-Lighting
(Society of Plastics Engineers, 2015)
Thermal management of LED lights can be arranged by deliberately influencing lighting components conduction capabilities and reducing the thermal contact resistance for various joining processes. The research details the possibilities thereof and shows the thermal contact resistance of plastic and
Konferenzveröffentlichung
Development of a Radian Friction Welding Machine Using the Circular Process with Limited Rotational Motion
(Society of Plastics Engineers, 2013)
The processing-technological limitations of components which can not be continuously rotated, either due to their length or marginal protrusions, make the realization of several potential applications using rotation welding unthinkable. The difficulties that arise while generating a high quality weld and are caused by large component tolerances and component warping are known. In order to extend the potential of friction welding, it is necessary to develop a new welding technology. In cooperation with Fischer ...
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...
Dissertation
Effect of heat treatment and iron content on the microstructure and mechanical properties of a secondary Al-Si-Cu alloy
(2019-05)
In this work the effect of heat treatments on the microstructure and mechanical properties of a secondary Al-Si-Cu alloy is studied. A Design of Experiments (DoE) was developed in order to optimize the heat treatment parameters and analyze the dissolution and fragmentation of the iron-rich inclusions as well as the improvement of the mechanical properties by non-equilibrium heat treatments. The iron-rich intermetallic inclusions were characterized as-cast and after heat treatment both by two-dimensional metallography ...
Buch
Optische Verformungsmessung an heterogenen Werkstoffsystemen
(kassel university press, 2020)
Im Rahmen der vorliegenden Arbeit wird die Anwendung der optischen Verformungsmessung auf heterogene Werkstoffsysteme untersucht, wobei dieses Verfahren auf unterschiedlichen Skalenebenen eingesetzt wird. Als erstes wird die digitale Bildkorrelation zur Temperaturüberwachung bei Hochtemperaturzugversuchen bis 350 °C an 0,6 mm dünnen lotplattierten Aluminiumprüfkörpern eingesetzt. Flächige Dehnungsauswertungen innerhalb des Prüfbereichs bestätigen die homogene Temperaturverteilung, wobei die Temperatur gleichzeitig ...
Aufsatz
Time-of-Flight Three Dimensional Neutron Diffraction in Transmission Mode for Mapping Crystal Grain Structures
(2017-08-25)
The physical properties of polycrystalline materials depend on their microstructure, which is the nano- to centimeter scale arrangement of phases and defects in their interior. Such microstructure depends on the shape, crystallographic phase and orientation, and interfacing of the grains constituting the material. This article presents a new non-destructive 3D technique to study centimeter-sized bulk samples with a spatial resolution of hundred micrometers: time-of-flight three-dimensional neutron diffraction (ToF ...
Aufsatz
Dynamic Tensile Deformation of High Strength Aluminum Alloys Processed Following Novel Thermomechanical Treatment Strategies
(2020-05-14)
Herein, the effects of a very recently introduced novel thermomechanical process route on the microstructural evolution and dynamic tensile deformation behavior of two different precipitation hardenable aluminum alloys, i.e., AA6082 and AA7075, are studied. The investigated materials are hot formed and quenched in differently tempered tools to reveal the influence of cooling rate. Microstructure analysis is conducted to study the influences of different cooling strategies on the microstructure evolution and prevailing ...
Buch
Rotatives Vibrationsschweißen
(kassel university press, 2017)
Schweißversuche mit den von dem Schweißmaschinenhersteller Fischer Kunststoff-Schweißtechnik GmbH entwickelten Prototypenmaschinen für das neuartige Rotative Vibrationsschweißen zeigen eine vergleichbare erforderliche Prozessführung und die bereits bekannten Ausprägungen der vier Schweißprozessphasen anderer Vibrationsschweißverfahren. Unter Verwendung unterschiedlicher Werkstoffe und Probekörpergeometrien zeigt sich, dass sich die Fügenahteigenschaften von mit dem Rotativen Vibrationsschweißverfahren gefügten ...
Buch
Struktur-Eigenschafts-Beziehung von Mischungen aus thermoplastischem PMMA mit vernetzten PMMA-Kolloiden
(kassel university press, 2016)
Ziel dieser Arbeit war es, ein Compound aus Partikeln aus untereinander vernetzten Polymerketten, sogenannten Kolloiden, und thermoplastischem Matrixmaterial basierend auf dem gleichen Monomer (MMA) aus ingenieurwissenschaftlicher Sicht zu charakterisieren und die Struktur-Eigenschafts-Beziehungen zu klären. Durchgeführt wurden die Untersuchungen an Compounds mit Kolloiden mit verschiedenen Größen, Vernetzungsgraden und Anteilen, die zunächst in Benzol mit dem Matrixmaterial, Plexiglas® 6N, vermischt wurden.
Neben ...