Search
Now showing items 71-79 of 79
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
Process Influences in the Combined Compacting and Back-Injection Process to Produce Back-Injected Self-Reinforced Composites (SRCs) – Analysis via Multiple Regression Modelling
(2021-11-21)
A new process to produce back-injected self-reinforced composites (SRCs) is presented. In contrast to other investigations on back-injection of SRCs, a process is presented which allows compacting and back injection of SRCs in one step where the SRCs are partly consolidated only via melt pressure inside the cavity. The mechanical properties of SRCs depend to a large extent on the process parameters of temperature and pressure during manufacture. These parameters are not yet known for back-injected areas. Sensors ...
Aufsatz
Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
(2022-03-08)
This publication investigates the adhesion between an injection molded component and a self-reinforced composite (SRC) produced in a combined compaction and back-injection process to produce back-injected self-reinforced composites. To study the influence of the process, the parameters barrel temperature, time of injection, and tool temperature were varied. In addition, samples were taken at different positions along the flow path. In light of the orthotropic material behavior of SRCs, investigations were conducted ...
Aufsatz
Holzdesign trifft Kunststofftechnik
(2022)
Werkstoffverbunde aus Holzgeweben in einer thermoplastischen Matrix verbinden die Idee des textilen Holzbaus mit der Faserverbundtechnologie. In einem Projekt werden Fassadenelemente aus solchen Wood Textile Composites hergestellt. Dabei spielt neben den mechanischen Anforderungen auch die gestalterische Seite und die Akzeptanz der zukünftigen Nutzer eine wichtige Rolle.
Aufsatz
Joining of Contact Pins and Conductive Compounds via Injection Molding – Influence of the Flow Situation on the Electrical Contact Resistance
(2020-04-09)
While a lot of research can be found in the field of bulk resistance of carbon filled polymers, comparatively few papers focus on contact resistance between compound and metal contacts. Due to that small number of researches that deal with contact resistances, studies of the influence of injection molding conditions and parameters on the contact resistance are also very rare. In contradiction to that, these influences on bulk resistance have been studied. The objective of this work was to investigate the electrical ...
Aufsatz
Effects of aging on the stress-induced martensitic transformation and cyclic superelastic properties in Co-Ni-Ga shape memory alloy single crystals under compression
(2022)
Co-Ni-Ga shape memory alloys attracted scientific attention as promising candidate materials for damping applications at elevated temperatures, owing to excellent superelastic properties featuring a fully reversible stress-strain response up to temperatures as high as 500 °C. In the present work, the effect of aging treatments conducted in a wide range of aging temperatures and times, i.e. at 300–400 °C for 0.25–8.5 h, was investigated. It is shown that critical features of the martensitic transformation are strongly ...
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...
Aufsatz
Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
(2022-03-03)
In this research paper, the effects of the combined compacting and back-injection process to produce back-injected self-reinforced composites on the mechanical properties of the self-reinforced composites (SRCs) are investigated. For this purpose, the parameters barrel temperature, time of injection and holding pressure were varied for the back injection. Tensile and bending tests were carried out on the SRCs. The results show that the mechanical properties depend to a large extent on the process parameters. The ...