Suche
Anzeige der Dokumente 1-10 von 79
Aufsatz
Quenching of High Entropy Alloys after Annealing
(2020)
The effect of cooling rate after annealing at 900 °C on the microstructure and hardness of high entropy alloys was investigated using two typical samples with the chemical composition of Co₁₆Cr₁₄.₅Fe₂₉Mn₁₁.₅Ni₂₉ and Co₁₁.₅Cr₇Fe₂₇Mn₂₇Ni₂₇(Nb₀.₀₈C₀.₅) (at%). The microstructural characterisation and hardness measurements were carried out by optical microscopy, scanning electron microscopy, wavelength-dispersive X-ray spectroscopy, electron back scattered diffraction, X-ray diffraction technique and Vickers hardness ...
Aufsatz
On the reliability of residual stress measurements in unidirectional carbon fibre reinforced epoxy composites
(2021-03-03)
The present work introduces a novel methodology to analyse non-uniform residual stresses in composite materials. For robust determination of stresses in complex structures made of different layers, it is first necessary to prove that residual stress analysis in a single layer structure can reliably be accomplished. In present work a unidirectional carbon fibre reinforced epoxy is investigated. For residual stress determination, the integral incremental hole drilling method is used. It is revealed that the standard ...
Aufsatz
Ti6Al4V lattice structures manufactured by electron beam powder bed fusion - Microstructural and mechanical characterization based on advanced in situ techniques
(2022-12-17)
Powder bed fusion (PBF) processes enable the manufacturing of complex components in a time- and cost-efficient manner. Especially lattice structures are currently focused since they show varying mechanical properties, including different deformation and damage behaviors, which can be used to locally tailor the mechanical behavior. However, the present process-structure-property relationships are highly complex and have to be understood in detail in order to enable an implementation of PBF manufactured lattice structures ...
Aufsatz
Effect of Grain Statistics on Micromechanical Modeling: The Example of Additively Manufactured Materials Examined by Electron Backscatter Diffraction
(2020-02-21)
Micromechanical modeling is one of the prominent numerical tools for the prediction of mechanical properties and the understanding of deformation mechanisms of metals. As input parameters, it uses data obtained from microstructure characterization techniques, among which the electron backscatter diffraction (EBSD) technique allows us to understand the nature of microstructural features, that are usually described by statistics. Because of these advantages, the EBSD dataset is widely used for synthetic microstructure ...
Aufsatz
Predicting Flow Stress Behavior of an AA7075 Alloy Using Machine Learning Methods
(2022-09-09)
The present work focuses on the prediction of the hot deformation behavior of thermo-mechanically processed precipitation hardenable aluminum alloy AA7075. The data considered focus on a novel hot forming process at different tool temperatures ranging from 24°C to 350°C to set different cooling rates after solution heat-treatment. Isothermal uniaxial tensile tests in the temperature range of 200°C to 400°C and at strain rates ranging from 0.001 s-¹ to 0.1 s-¹ were carried out on four different material conditions. ...
Aufsatz
Effects of Aging under Stress on Mechanical Properties and Microstructure of EN AW 7075 Alloy
(2021-07-20)
In the present study, microstructural and mechanical properties of EN AW 7075 following stress-aging were assessed. For this purpose, properties of stress-aged samples were compared with values obtained for conventionally aged counterparts. It is revealed that the strength and hardness of EN AW 7075 can be increased by the presence of external stresses during aging. Precipitation kinetics were found to be accelerated. The effects of conventional and stress-aging on the microstructure were analyzed using synergetic ...
Aufsatz
Effect of Friction Stir Processing on Microstructural, Mechanical, and Corrosion Properties of Al-Si12 Additive Manufactured Components
(2020-01-03)
Additive manufacturing (AM) is an advanced manufacturing process that provides the opportunity to build geometrically complex and highly individualized lightweight structures. Despite its many advantages, additively manufactured components suffer from poor surface quality. To
locally improve the surface quality and homogenize the microstructure, friction stir processing (FSP) technique was applied on Al-Si12 components produced by selective laser melting (SLM) using two different working media. The effect of FSP on ...
Aufsatz
Influence of complex geometries on the properties of laser-hardened surfaces
(2020-04-25)
Laser surface hardening provides for many advantages in terms of flexible production due to very localized and controlled energy input into the material. Laser processing offers the possibility to treat surfaces in order to locally strengthen the areas that are prone to fatigue cracking. It is well known that laser energy absorption depends on many parameters, e.g., the surface structure and the surface orientation. The incident angle of the laser beam plays a key role in this regard. When complex geometries like ...
Aufsatz
Consequences of Deep Rolling at Elevated Temperature on Near-Surface and Fatigue Properties of High-Manganese TWIP Steel X40MnCrAl19-2
(2021-11-05)
Due to pronounced work-hardening induced by the complex interplay of deformation mechanisms such as dislocation slip, twinning and/or martensitic phase transformation, high-manganese steels represent a class of materials well-suited for mechanical surface treatment. In the present study, the fatigue behavior of a high-mangsanese steel showing twinning-induced plasticity (TWIP) effect at room temperature (RT) was investigated after deep rolling at 550 °C. Results are compared to a former study discussing the behavior ...
Aufsatz
Excellent superelasticity in a Co-Ni-Ga high-temperature shape memory alloy processed by directed energy deposition
(2020-04-30)
A Co-Ni-Ga high-temperature shape memory alloy has been additively manufactured by directed energy deposition. Due to the highly anisotropic microstructure, i.e. columnar grains featuring a strong near-⟨001⟩ texture in build direction, the as-built material is characterized by a very low degree of constraints and, thus, shows excellent superelasticity without conducting a post-process heat treatment. As characterized by in situ deformation testing and post-mortem microstructural analysis, additive manufacturing ...