Suche
Anzeige der Dokumente 141-150 von 170
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...
Aufsatz
Influences on the mechanical properties of SRCs in a combined compacting and back injecting process
(2022-03-03)
In this research paper, the effects of the combined compacting and back-injection process to produce back-injected self-reinforced composites on the mechanical properties of the self-reinforced composites (SRCs) are investigated. For this purpose, the parameters barrel temperature, time of injection and holding pressure were varied for the back injection. Tensile and bending tests were carried out on the SRCs. The results show that the mechanical properties depend to a large extent on the process parameters. The ...
Konferenzveröffentlichung
Multicomponent Injection Molding Of Thermoplastics And Liquid Silicone Rubber (LSR) – Either Cured By Heat Or UV Light
(Society of Plastics Engineers, 2016)
For processing thermally curing liquid silicone rubber (LSR) as well as UV light curing LSR for multicompo-nent injection molding with thermoplastics in an compa-rable way a processing center was designed and set into operation.
For the production of the multicomponent specimens a modular tool was designed. In there a thermoplastic plate gets molded on the one side, then gets transferred auto-matically by a robot system and gets overmolded by the silicone on the other side. The complete silicone side of the tool is ...
Aufsatz
A Novel Approach to Robustly Determine Residual Stress in Additively Manufactured Microstructures Using Synchrotron Radiation
(2021-07-29)
In recent decades additive manufacturing (AM) for years has been in focus of academia and industry as its underlying production principle allows for the realization of designs of unprecedented geometrical complexity. However, often such structures are not realized due to the lack of understanding of structural and mechanical properties, this fact amongst others related to the unique microstructures established by the related processes. In this context, residual stresses, highly affected by the scan strategy and process ...
Aufsatz
Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys
(2021-07-26)
In situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is ...
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
On the Monotonic and Cyclic Behavior of an Al-Mg-Zn-Cu-Si Compositionally Complex Alloy
(2023-08-03)
In present work, the monotonic and cyclic properties of a novel Al-Mg-Zn-Cu-Si compositionally complex alloy (CCA) are investigated. Microstructural studies reveal that a eutectic phase and fishbone-type structures are embedded in the Al-matrix. The mechanical properties of this CCA obtained under compressive loading are found to be promising. However, low ultimate strength and brittle behavior are seen under tension. The fatigue performance of the alloy in the low-cycle fatigue (LCF) regime is poor. Microstructural ...
Aufsatz
Liquid Silicone Rubber Foams Made with Water as Blowing Agent
(2021-08-18)
Liquid silicone rubber (LSR) is primarily used in injection molding. Foamed molded parts made of LSR are almost nonexistent because the process reliability of LSR foam injection molding is currently not given. It makes sense to have suitable foaming processes for this material as well, because the density of this elastomer is about 1.15 g cm−3. With the injection molding process presented herein for foaming LSR, density reductions of up to 40% can be achieved. In this process, up to 3% by weight of water is added to ...
Aufsatz
Hot Sheet Metal Forming Strategies for High-Strength Aluminum Alloys: A Review—Fundamentals and Applications
(2023-05-17)
In the past decade, aluminum alloys have become important structural materials in the automotive industry, thanks to their low density, high strength, high fracture toughness, and good fatigue performance. However, an important limitation of aluminum alloys is their poor formability at room temperature; as a result, numerous studies have been conducted with the aim of developing forming techniques to overcome this and facilitate the forming of more complex-shaped components. Following an overview on the metallurgical ...