Suche
Anzeige der Dokumente 1-10 von 17
Aufsatz
Influence of Accelerated Aging on the Fiber-Matrix Adhesion of Regenerated Cellulose Fiber-Reinforced Bio-Polyamide
(2023-03-23)
With regard to the sustainability and biological origin of plastic components, regenerated cellulose fiber (RCF)-reinforced polymers are expected to replace other composites in the future. For use under severe conditions, for example, as a housing in the engine compartment, the resistance of the composites and the impact on the fiber and fiber-matrix adhesion must be investigated. Composites of bio-polyamide with a reinforcement of 20 wt.% RCF were compounded using a twinscrew extruder. The test specimens were ...
Aufsatz
Theoretical study of spin polarization in multiphoton ionization of Xe
(2023-04-21)
Spin polarization in the multiphoton above-threshold ionization of 5p3/2- and 5p1/2-electrons of Xe with intense 395nm, circularly polarized laser pulses, is investigated theoretically. For this purpose, we solve the time-dependent Schrödinger equation on the basis of spherical spinors. We, thus, simultaneously propagate the spin-up and spin-down single-active-electron wave packets, driven by the laser pulses in the ionic potential, which includes the spin–orbit interaction explicitly. The present theoretical results ...
Aufsatz
Comparative Life Cycle Assessment of Carbon Dioxide Mineralization Using Industrial Waste as Feedstock to Produce Cement Substitutes
(2023-05-16)
The mineralization of carbon dioxide offers a way to permanently sequester carbon while producing construction materials, combining the concepts of carbon capture and utilization (CCU) and carbon capture and storage (CSS). However, it is important to evaluate different mineralization processes in terms of their environmental impact. This study provides the first comparative life cycle assessment (LCA) analysis that focuses on the utilization of industrial waste materials. We analyzed the climate and material footprint ...
Aufsatz
Analysis and Validation of Varied Simulation Parameters in the Context of Thermoplastic Foams and Special Injection Molding Processes
(2023-04-28)
The simulation solutions of different plastic injection molding processes are as multifaceted as the field of injection molding itself. In this study, the simulation of a special injection molding process, which generates partially foamed integral components, was parameterized and performed. This partial and physical foaming is realized by a defined volume expansion of the mold cavity. Using the injection molding simulation software Moldex 3D, this so-called Pull and Foam process was digitally reconstructed and ...
Aufsatz
Ferrocene-Based N-Heterocyclic Plumbylenes [Fe{(η⁵- C₅H₄)NSiMe₂R}₂Pb:]: Influence of the Steric Demand of the NSubstituents on Their Dimerization via C-H Activation with Pbᴵᴵ
(2023-05-12)
Ferrocene-based N-heterocyclic plumbylenes fc[(NSiMe₂R)₂Pb:] (1; fc=1,1’-ferrocenylene) are easily accessible by transamination from [(Me₃Si)₂N]₂Pb and the corresponding 1,1’-diaminoferrocene derivatives fc(NHSiMe₂R)₂. They may form unconventional dimers 2 by a process, which causes the cleavage of a cyclopentadienyl C−H bond and the formation of a Pb−C and an N−H bond. The monomer-dimer equilibrium (2 1⇆2) has been addressed experimentally and computationally. It critically depends on the steric demand of the ...
Aufsatz
Observation of a Long-lived Electronic Coherence Modulated by Vibrational Dynamics in Molecular Nd³+- Complexes at Room Temperature
(2023-03-23)
Temporally delayed, phase-locked coherent pairs of near IR femtosecond laser pulses were employed to study electronic coherences in molecular Nd³+-complexes at room temperature. Dissolved and solid complexes were studied under a confocal microscope set-up with fluorescence detection. The observed electronic coherence on a few hundred femtoseconds time scale is modulated by additional coherent wave packet dynamics, which we attribute mainly to be vibrational in nature. In future, the complexes may serve as prototypes ...
Aufsatz
Reduction Behavior of Anisyl-substituted P-Ferrocenyl Phospholes
(2023-05-26)
P-Ferrocenylphospholes with differing substituents in α-position have been synthesized and their identity and purity was confirmed using multinuclear NMR spectroscopy, MS, elemental analysis and single crystal X-ray diffraction. Furthermore, the redox properties have been explored with electrochemical measurements. Transferring the reduction to a preparative scale using lithium leads to reductive P−C bond cleavage furnishing the corresponding phospholide which has been transformed to P-tert-butyl substituted phosphole. ...
Aufsatz
Emission and Mechanical Properties of Glass and Cellulose Fiber Reinforced Bio-Polyamide Composites
(2023-06-07)
Climate change, access, and monopolies to raw material sources as well as politically motivated trade barriers are among the factors responsible for a shortage of raw materials. In the plastics industry, resource conservation can be achieved by substituting commercially available petrochemical-based plastics with components made from renewable raw materials. Innovation potentials are often not used due to a lack of information on the use of bio-based materials, efficient processing methods, and product technologies ...
Aufsatz
The Influence of Thermal and Mechanical Stress on the Electrical Conductivity of ITO-Coated Polycarbonate Films
(2023-05-31)
The influence of thermomechanical stress on the conductivity of indium tin oxide (ITO)-coated polycarbonate (PC) films was investigated. PC is the industry’s standard material for window panes. ITO coatings on polyethylene terephthalate (PET) films are the main commercially available option; as such, most investigations refer to this combination. The investigations in this study aim to investigate the critical crack initiation strain at different temperatures and crack initiation temperatures for two different coating ...
Aufsatz
Influence of Chitosan and Grape Seed Extract on Thermal and Mechanical Properties of PLA Blends
(2023-03-22)
Blends based on polylactic acid (PLA), chitosan, and grape seed extract (GE) were prepared by extrusion and injection molding. The effect of chitosan (5% and 15% on PLA basis) and natural extract (1% on PLA basis) incorporated into the PLA host matrix was explored regarding the thermal and mechanical properties. GE showed antioxidant activity, as determined by the DPPH assay method. Chitosan and GE affect the degree of crystallinity up to 30% as the polysaccharide acts as a nucleating agent, while the extract reduces ...