Suche
Anzeige der Dokumente 1-10 von 16
Aufsatz
Influence of hot deformation on the precipitation hardening of high-strength aluminum AA7075 during thermo-mechanical processing
(2021-04-21)
The aim of this work was to investigate the effect of hot deformation on the aging behavior of precipitation-hardenable aluminum alloy AA7075 within a novel thermo-mechanical forming process, in order to gain insight into its precipitation kinetics. For this purpose, the material was formed at 420 °C after undergoing solution treatment to different strain levels ranging from 2% to 10% to obtain different dislocation densities. After undergoing hot deformation, aging at 120 °C with different parameters was carried out ...
Aufsatz
High-Speed Laser Cladding on Thin-Sheet-Substrates—Influence of Process Parameters on Clad Geometry and Dilution
(2021-08-09)
Laser-based Directed Energy Deposition (DED-LB) represents a production method of growing importance for cladding and additive manufacturing through the use of metal powders. Yet, most studies utilize substrate materials with thicknesses of multiple millimeters, for which laser cladding of thin-sheet substrates with thicknesses less than 1 mm have only been scarcely studied in the literature. Most studies cover the use of pulsed laser sources, since sheet distortion due to excess energy input is a key problem in laser ...
Aufsatz
Extension of Gap Bridgeability and Prevention of Oxide Lines in the Welding Seam through Application of Tools with Multi-Welding Pins
(2021-07-30)
Friction stir welding has become important in many areas of production and is increasingly used for joining aluminum components. For long welding seams, conventional tools with only one welding pin reach their technical limitations due to low gap bridgeability. When welding aluminum, the stirred in surface layers, such as oxides, lead to a decrease in static and dynamic strength since linear accumulations are formed in the welding seam. The aim of the present study is to increase the gap bridgeability using tools ...
Aufsatz
Use of Design of Experiments (DoE) to Model the Sulphate Agent Amount of (Ultra)Finely Ground and Fast Hardening Portland Cement Clinker
(2021-09-25)
This paper presents a model to calculate the sulphate agent amount and sulphate agent ratio for fine grounded and fast hardening Portland cement clinker. Despite sufficient knowledge about the influence of calcium sulphate on the hydration process of cement, the sulphate agent amount is mostly adjusted empirically. As a result, often a wide and unfeasible experimental matrix has to be tested. In this work, Design of Experiments (DoE) was used in combination with in-situ X-ray diffraction (XRD) tests to accurately ...
Aufsatz
Laser Powder Bed Fusion Processing of Fe-Mn-Al-Ni Shape Memory Alloy—On the Effect of Elevated Platform Temperatures
(2021-01-20)
In order to overcome constraints related to crack formation during additive processing (laser powder bed fusion, L-BPF) of Fe-Mn-Al-Ni, the potential of high-temperature L-PBF processing was investigated in the present study. The effect of the process parameters on crack formation, grain structure, and phase distribution in the as-built condition, as well as in the course of cyclic heat treatment was examined by microstructural analysis. Optimized processing parameters were applied to fabricate cylindrical samples ...
Aufsatz
Adsorption of PCE in alkali-activated materials analysed by fluorescence microscopy
(2021-10-18)
The realisation of high-performance concrete mixtures requires the use of superplasticizers to achieve a low water/binder ratio and thus high strengths. Polycarboxylate ethers (PCE) are mostly used as superplasticizers. The effectiveness of these superplasticizers depends on their chemical structure, the binders’ alkaline environment and the ions present in the pore solution of the binder. In high alkaline systems like some alkali-activated materials no effective superplasticizer have been found yet. To unravel the ...
Aufsatz
Measurement and analysis of residual stresses and warpage in fiber reinforced plastic and hybrid components
(2021-02-16)
Glass/carbon fiber reinforced plastic (GFRP/CFRP) and hybrid components have attracted increasing attention in lightweight applications. However, residual stresses induced in the manufacturing process of these components can result in warpage and, eventually, negatively affect the mechanical performance of the composite structures. In the present work, GFRP, CFRP, GFRP/steel and CFRP/steel hybrid components were manufactured through the prepreg-press-technology always employing the same process parameters. The residual ...
Aufsatz
Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys
(2021-07-26)
In situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is ...
Aufsatz
Simultaneous impact modified and chain extended glass fiber reinforced poly(lactic acid) composites: Mechanical, thermal, crystallization, and dynamic mechanical performance
(2021-02-05)
Herein, glass fiber (GF) reinforced binary, ternary, and quaternary poly(lactic acid) (PLA) composites were prepared. Toughening, and chain extension of PLA was achieved through the incorporation of impact modifier and chain extender and their concurrent effects on the spectroscopic, crystallization, mechanical, thermal, and thermomechanical properties of the composites were investigated. High mechanical properties of GF influenced the mechanical performance of the composites. However, GF alone could not restrict the ...
Aufsatz
Liquid Silicone Rubber Foams Made with Water as Blowing Agent
(2021-08-18)
Liquid silicone rubber (LSR) is primarily used in injection molding. Foamed molded parts made of LSR are almost nonexistent because the process reliability of LSR foam injection molding is currently not given. It makes sense to have suitable foaming processes for this material as well, because the density of this elastomer is about 1.15 g cm−3. With the injection molding process presented herein for foaming LSR, density reductions of up to 40% can be achieved. In this process, up to 3% by weight of water is added to ...