Search
Now showing items 1891-1900 of 1944
Aufsatz
Pathways toward the Use of Non-Destructive Micromagnetic Analysis for Porosity Assessment and Process Parameter Optimization in Additive Manufacturing of 42CrMo4 (AISI 4140)
(2024-02-20)
Laser-based powder bed fusion of metals (PBF-LB/M) is a widely applied additive manufacturing technique. Thus, PBF-LB/M represents a potential candidate for the processing of quenched and tempered (Q&T) steels such as 42CrMo4 (AISI 4140), as these steels are often considered as the material of choice for complex components, e.g., in the toolmaking industry. However, due to the presence of process-induced defects, achieving a high quality of the resulting parts remains challenging in PBF-LB/M. Therefore, an extensive ...
Aufsatz
Modification of self-reinforced composites (SRCs) via film stacking process
(2022-02-25)
This work presents the mechanical behavior of self-reinforced composites (SRCs) manufactured and modified via film stacking. For modification, interleaved films made of polypropylene (PP), a thermoplastic elastomer and a polyolefin engage were combined in different ways to induce the elastic modifier into the matrix material. The content of modifier was also varied in two ways. First, the films were produced out of a single material and second out of a compound. So, the same content of modifier was implemented in two ...
Aufsatz
Bend Straightening of a Carbonitrided Gear Shaft – Consequences on Residual Stresses and Retained Austenite near the Surface
(2017-06-20)
Carbonitriding of shafts in drive technology is strongly connected with distortion. Bend straightening is an important process step in order to eliminate distortion without removing the hardened surface layer. As shown in several investigations, even for simple part geometries, bending induced stresses and plastic deformations have a strong impact not only on the residual stress state but also on the microstructure after straightening. As gear shafts become increasingly filigree and complex in their geometry, the ...
Aufsatz
Investigation of the adhesive strength in a combined compaction and back-injection process to produce back-injected self-reinforced composites (SRCs)
(2022-03-08)
This publication investigates the adhesion between an injection molded component and a self-reinforced composite (SRC) produced in a combined compaction and back-injection process to produce back-injected self-reinforced composites. To study the influence of the process, the parameters barrel temperature, time of injection, and tool temperature were varied. In addition, samples were taken at different positions along the flow path. In light of the orthotropic material behavior of SRCs, investigations were conducted ...
Aufsatz
Climatic Ageing of Components of Polymer Based Electrochromic Devices
(2013-09-09)
Combining a shading function and a polycarbonate window displays an attractive alternative to the currently employed glass roof in vehicles. However, the ageing of such a device must be investigated before any application. Therefore, our investigations focus on the ageing of the components of a polycarbonate based electrochromic device. The optical, electrical, mechanical and electrochemical properties of the ion storage layer as well as the substrate will be assessed after storage in a climate with a high humidity ...
Aufsatz
Enhancing crop-livestock systems: Unveiling the impact of leaf stripping on maize hybrid yield in Sundarbazar-Lamjung, Nepal
(2024-03-12)
In local maize agro-ecosystems in Nepal leaf stripping is, historically, practiced as a source of fodder for livestock. However, its effects on hybrid maize have not been studied. The aim of this study was to determine how defoliation below the cob affects the grain and fodder production of hybrid maize and what value the stripped leaves have as fodder for ruminants. Seven hybrid maize cultivars were evaluated for their response to leaf stripping in a randomized complete block design with three replications in ...
Aufsatz
Spatio-temporal resolution studies on a highly compact ultrafast electron diffractometer
(2015)
Time-resolved diffraction with femtosecond electron pulses has become a promising technique to directly provide insights into photo induced primary dynamics at the atomic level in molecules and solids. Ultrashort pulse duration as well as extensive spatial coherence are desired, however, space charge effects complicate the bunching of multiple electrons in a single pulse.Weexperimentally investigate the interplay between spatial and temporal aspects of resolution limits in ultrafast electron diffraction (UED) on our ...
Aufsatz
Ordoliberalism Out of Order? The Fragile Constitutionality of Greek Austerity (Part Two)
(2020-06)
This is the second part of a two-part post. The first part, available here, considered the historical background of the concept of constitutional order and its relation to the ordoliberal project. Judicial independence was examined in parallel with central bank independence, with each understood as a means of insulating policy from social and democratic pressures and also as a means of enacting and maintaining fiscal discipline and market-conforming order. It also included some preliminary observations on the relation ...
Aufsatz
Holzdesign trifft Kunststofftechnik
(2022)
Werkstoffverbunde aus Holzgeweben in einer thermoplastischen Matrix verbinden die Idee des textilen Holzbaus mit der Faserverbundtechnologie. In einem Projekt werden Fassadenelemente aus solchen Wood Textile Composites hergestellt. Dabei spielt neben den mechanischen Anforderungen auch die gestalterische Seite und die Akzeptanz der zukünftigen Nutzer eine wichtige Rolle.
Aufsatz
A Literature Review on Solid Waste Management and Disposal Behavior at the Base of the Pyramid
(2024-03-10)
Consumer behavior in disposing of products has substantial consequences for the environment that affect all of us. Waste management is a major challenge faced by many developing countries, underlining the relevance of this literature review. Even when academia tries to shed light on this field, it often fails to consider that waste management must be approached differently in less developed countries, which differ dramatically from advanced countries, especially with regard to consumers’ behavioral characteristics. ...