Suche
Anzeige der Dokumente 21-30 von 32
Aufsatz
Time-of-Flight Three Dimensional Neutron Diffraction in Transmission Mode for Mapping Crystal Grain Structures
(2017-08-25)
The physical properties of polycrystalline materials depend on their microstructure, which is the nano- to centimeter scale arrangement of phases and defects in their interior. Such microstructure depends on the shape, crystallographic phase and orientation, and interfacing of the grains constituting the material. This article presents a new non-destructive 3D technique to study centimeter-sized bulk samples with a spatial resolution of hundred micrometers: time-of-flight three-dimensional neutron diffraction (ToF ...
Masterarbeit
Free decay testing of a semisubmersible offshore floating platform for wind turbines in model scale
(2017-12-20)
Wind turbines can be installed on floating platforms in order to use wind resources, which blow above the deep sea. The presented research investigates the hydrodynamic behaviour of the Olav Olsen Concrete Star floater in free decay motion. The floater is a new design of a semisubmersible offshore floating platform for wind turbines. The thesis describes the physical free decay testing of a 1/40 plastic scale model in a water basin as well as numerical simulations of the same test cases with the aero-hydro-servo-elastic ...
Buch
Rotatives Vibrationsschweißen
(kassel university press, 2017)
Schweißversuche mit den von dem Schweißmaschinenhersteller Fischer Kunststoff-Schweißtechnik GmbH entwickelten Prototypenmaschinen für das neuartige Rotative Vibrationsschweißen zeigen eine vergleichbare erforderliche Prozessführung und die bereits bekannten Ausprägungen der vier Schweißprozessphasen anderer Vibrationsschweißverfahren. Unter Verwendung unterschiedlicher Werkstoffe und Probekörpergeometrien zeigt sich, dass sich die Fügenahteigenschaften von mit dem Rotativen Vibrationsschweißverfahren gefügten ...
Buch
Beitrag zur Herstellung 3-dimensionaler Kunststoffscheiben mit integrierter Funktion zur Veränderung der Transparenz durch Elektrochromie
(kassel university press, 2017)
Ziel dieser Arbeit ist es Möglichkeiten der Kunststoffverarbeitung aufzuzeigen, um feste 3D Bauteile mit elektrochromen (EC) Eigenschaften herzustellen. Die momentanen EC Anwendungen reduzieren sich fast ausschließlich auf plane Fensterscheiben aus Glas für die Gebäudeverglasung. Vereinzelt gibt oder gab es aber auch Anwendungen im Flugzeug- und Automobilbau. Die Anforderungen bezüglich des Schaltverhaltens sind in den erwähnten Bereichen sehr hoch und führen zu einer kostenintensiven Produktion.
Am Anfang der Arbeit ...
Aufsatz
Energy Resolved Residual Stress Analysis with Laboratory X-Ray Sources
(2017-04-17)
It is well known that existing residual stress fields play an important role for strength and lifetime of components. Consequently there is a great interest in the availability of fast, reliable and possibly nondestructive methods for their determination. In this context, X-ray diffraction methods play an important role in technical practice as well as in scientific research. They are based on the determination of lattice strains from which residual stresses are determined applying Hooke's law with appropriate elastic ...
Aufsatz
Prozessintegration von induktiver Wärmebehandlung und Festwalzen – sichere und zuverlässige Komponenten mit hoher Schwingfestigkeit
(2017-02-08)
Mechanische Oberflächenbehandlungen, beispielsweise das Festwalzen, spielen in der technischen Praxis eine bedeutende Rolle und tragen wesentlich zur Steigerung der Zuverlässigkeit hochbeanspruchter Komponenten bei. In einer Reihe von Fällen wurde gezeigt, dass eine Erhöhung der Prozesstemperatur die Wirksamkeit der Verfahren noch steigert, weil dies zu einer besseren Stabilisierung der eingebrachten Druckeigenspannungen führt. Eine wesentliche Voraussetzung zur Einführung dieser Verfahren in die Praxis ist allerdings, ...
Aufsatz
Bend Straightening of a Carbonitrided Gear Shaft – Consequences on Residual Stresses and Retained Austenite near the Surface
(2017-06-20)
Carbonitriding of shafts in drive technology is strongly connected with distortion. Bend straightening is an important process step in order to eliminate distortion without removing the hardened surface layer. As shown in several investigations, even for simple part geometries, bending induced stresses and plastic deformations have a strong impact not only on the residual stress state but also on the microstructure after straightening. As gear shafts become increasingly filigree and complex in their geometry, the ...
Aufsatz
Investigations on Tightness of Polymer-Metal Hybrids in Environments with Thermal, Media, and Mechanical Loads
(2017-07-31)
With polymer-metal hybrids becoming more commonly used as structural components it was investigated how they perform in complex environments with combined thermal, media, and mechanical loads. Special attention was put on media tightness under said loads. This paper sums up the activities of the polymer technology research group of the University of Kassel on hybrids produced by overmolding metal inserts. Investigations concerning joint strength and influence of (cyclic) temperature loads and chemical corrosion on ...
Aufsatz
Mechanical Properties of Polydimethylsiloxane as a Function of the Amount and Type of Crosslinking Agent
(2017-06-13)
In this investigation, a high-consistency rubber (HCR) was mixed with five different, typically used crosslinking agents that are based on organic peroxide. Furthermore, the amount of crosslinking agent was varied in order to quantify the effect on the mechanical properties. All materials were processed in a hot pressing process, and, subsequently, post-cured. The properties were characterized by the measurement of the swelling ratio, shore A-hardness, rebound resilience and tensile test. We successfully proved that ...
Konferenzveröffentlichung
Influence Of The Fiber-Matrix-Interaction On The Fracture Behavior Of Regenerated Cellulose Fiber Reinforced Polypropylene
(Society of Plastics Engineers, 2017)
This investigation focuses on the fiber-matrix-interaction of man-made cellulose fibers (RCF) in a PP matrix with an additional MAPP content using an energetic evaluation of the single fiber pull-out test (SFPT). Furthermore glass fibers were characterized for reference purposes. With the SFPT the interfacial shear strength (IFFS) and the critical fiber length (lc) as well as the consumed energy of a fiber pull-out and a fiber rupture were determined. In a following step the resulting values of lc were related to the ...