Suche
Anzeige der Dokumente 161-170 von 201
Aufsatz
Cyclic Deformation Response of Ultra-fine Grained Titanium at Elevated Temperatures
(2019)
This study focuses on the high-temperature cyclic deformation response (CDR) of ultra-fine grained (UFG) titanium of commercial purity (grade 4) processed via equal channel angular extrusion as a severe plastic deformation method. Low-cycle fatigue experiments were conducted at elevated temperatures up to 600 °C and at strain amplitudes ranging from 0.2% to 0.6%. Besides temperature and strain amplitude, the influence of two processing routes (8BC and 8E) on the fatigue characteristics of UFG Ti was examined. It is ...
Aufsatz
Effect of grain size on the very high cycle fatigue behavior and notch sensitivity of titanium
(2019)
The very high-cycle fatigue performances of coarse-grained and ultrafine-grained titanium samples with different geometries at ambient temperature and various stress amplitudes were investigated. Severe plastic deformation improves monotonic strength of titanium at the cost of a loss in ductility. Ultrafine-grained titanium demonstrates a superior fatigue performance compared to that of coarse-grained counterparts in the high-cycle fatigue regime, however, suffers notch sensitivity. Furthermore, in the very high-cycle ...
Aufsatz
Parameter identification for constitutive models of innovative textile composite materials using digital image correlation
(2019-11-18)
This contribution focuses on an innovative composite material consisting of textile layers made from continuous wooden fibers embedded in a thermoplastic matrix. A finite element simulation of potential use‐cases is planned to support the development process and to study the suitability of the material in an architectural context. The simulation is based on a constitutive model assuming homogenous orthotropic elastic behavior and will be expanded to include multiscale modeling in future research. The material parameters ...
Aufsatz
Influence of deep rolling at different temperatures on near-surface and mechanical properties of a Maraging C250 steel
(2024-04-27)
Due to an outstanding combination of high strength and fracture toughness Maraging steels are used in numerous industries, e.g., in the aerospace sector. The high strength can be attributed to precipitation strengthening by conventional age-hardening heat treatments. However, as many of the envisaged applications will suffer from cyclic loadings, the fatigue properties are of significant interest in terms of a reliable use. Generally, Maraging steels are characterized by a relatively low fatigue strength limiting the ...
Aufsatz
Parameter recommendation for injection molding based on similarity analysis of injection molded parts
(2023)
Injection molding is a widespread manufacturing process for producing complex plastic shapes. The process is controlled by a large number of parameters, which show interactions with each other. Thereby the determination of an optimal operating point during sampling is a resource-consuming and demanding task. The data, which is generated during sampling, is usually not used for subsequent sampling processes. In the context of Industry 4.0, manufacturing companies attempt to optimize production efficiency to save time ...
Aufsatz
Baumwolle als Faserverstärkung
(2023)
Jedes Jahr landen große Mengen Textilen auf Deponien oder in der thermischen Verwertung. Ein Teil dieser Abfälle könnte allerdings auch als Rohstoffe für Verbundwerkstoffe dienen. Baumwollfasern eignen sich etwa als Verstärkungsfasern, die die mechanischen Eigenschaften von biobasierten Kunststoffen steigern. Durch die Nutzung solcher Abfallströme können in Zukunft kostengünstig und biobasiert Materialien verstärkt werden.
Aufsatz
Oxide Modified Iron in Electron Beam Powder Bed Fusion - From Processability to Corrosion Properties
(2022-03-07)
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material composition, and the solidification behavior of the material considered. However, when complex specific requirements have to be met, a targeted part design is highly challenging. In the field of biodegradable implant surgery, a cytocompatible material of an application-adapted ...
Aufsatz
Investigation of residual stresses in polypropylene using hot plate welding
(2020-08-05)
During the cooling process of the molten material, residual stresses appear because the reduced volume of the cooled material cannot fully fill the space formerly occupied by the molten material. The morphology in and around the weld is formed by different factors depending on the material and process parameters. Different morphological structures relate to different mechanical properties. The process parameters and the welding results including morphology and residual stress are linked together. In this article, ...
Aufsatz
Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
(2022-09-16)
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based ...
Aufsatz
Process Influences in the Combined Compacting and Back-Injection Process to Produce Back-Injected Self-Reinforced Composites (SRCs) – Analysis via Multiple Regression Modelling
(2021-11-21)
A new process to produce back-injected self-reinforced composites (SRCs) is presented. In contrast to other investigations on back-injection of SRCs, a process is presented which allows compacting and back injection of SRCs in one step where the SRCs are partly consolidated only via melt pressure inside the cavity. The mechanical properties of SRCs depend to a large extent on the process parameters of temperature and pressure during manufacture. These parameters are not yet known for back-injected areas. Sensors ...