Suche
Anzeige der Dokumente 51-60 von 171
Aufsatz
Morphology-property-relationship of thermo-mechanically graded self-reinforced polypropylene composites
(2015-02-17)
In this paper the relationship between different composite morphologies and their mechanical properties is to be investigated. By manufacturing two different tape-based polypropylene composites in a compression moulding process, four varying degrees of compaction will be generated. The morphological structure is analyzed using confocal laser light microscopy and wet chemically etched specimen cross-sections. The etching process removes the amorphous phase in the polymer, making the macromolecular orientations and ...
Aufsatz
A framework for the computer-aided planning and optimisation of manufacturing processes for components with functional graded properties
(2015-02-17)
In this contribution a framework for the computer-aided planning and optimisation of functional graded components is presented. The framework is divided into three modules - the "Component Description", the "Expert System" for the synthetisation of several process chains and the "Modelling and Process Chain Optimisation". The Component Description module enhances a standard computer-aided design (CAD) model by a voxel-based representation of the graded properties. The Expert System synthesises process steps stored ...
Dissertation
Simulationen und Experimente im Schwellenwertbereich zur Aufklärung der Risswachstumsmechanismen in einer Aluminiumlegierung
(2020)
Lange Risse, die bei Belastungen nahe des Schwellenwerts wachsen, können Ausbreitungscharakteristika zeigen, welche denen kurzer Stadium I-Risse ähneln. Neben einer lokalen Blockade der Rissfront durch Teilchen einer zweiten Phase ist ein schubspannungsgesteuerter Rissfortschritt ein interessanter Effekt, der bei diesen Belastungsbedingungen auftritt. Das berichtete Verhalten wird im Rahmen dieser Arbeit auf das Rissspitzenfeld zurückgeführt. Zu diesem Zweck wurden Risswachstumsexperimente mit angerissenen Flachproben ...
Aufsatz
Quenching of High Entropy Alloys after Annealing
(2020)
The effect of cooling rate after annealing at 900 °C on the microstructure and hardness of high entropy alloys was investigated using two typical samples with the chemical composition of Co₁₆Cr₁₄.₅Fe₂₉Mn₁₁.₅Ni₂₉ and Co₁₁.₅Cr₇Fe₂₇Mn₂₇Ni₂₇(Nb₀.₀₈C₀.₅) (at%). The microstructural characterisation and hardness measurements were carried out by optical microscopy, scanning electron microscopy, wavelength-dispersive X-ray spectroscopy, electron back scattered diffraction, X-ray diffraction technique and Vickers hardness ...
Aufsatz
On the reliability of residual stress measurements in unidirectional carbon fibre reinforced epoxy composites
(2021-03-03)
The present work introduces a novel methodology to analyse non-uniform residual stresses in composite materials. For robust determination of stresses in complex structures made of different layers, it is first necessary to prove that residual stress analysis in a single layer structure can reliably be accomplished. In present work a unidirectional carbon fibre reinforced epoxy is investigated. For residual stress determination, the integral incremental hole drilling method is used. It is revealed that the standard ...
Aufsatz
Comparative investigation of two-dimensional imaging methods and X-ray tomography in the characterization of microstructure
(2017-10-02)
The microstructural features of three different materials have been quantified by means of 2D image analysis and X-ray micro-computer tomography (CT) and the results were compared to determine the reliability of the 2D analysis in the material characterization. The 3D quantification of shrinkage pores and Fe-rich inclusions of an Al-Si-Cu alloy by X-ray tomography was compared with the statistical analysis of the 2D metallographic pictures and a significant difference in the results was found due to the complex ...
Aufsatz
Ti6Al4V lattice structures manufactured by electron beam powder bed fusion - Microstructural and mechanical characterization based on advanced in situ techniques
(2022-12-17)
Powder bed fusion (PBF) processes enable the manufacturing of complex components in a time- and cost-efficient manner. Especially lattice structures are currently focused since they show varying mechanical properties, including different deformation and damage behaviors, which can be used to locally tailor the mechanical behavior. However, the present process-structure-property relationships are highly complex and have to be understood in detail in order to enable an implementation of PBF manufactured lattice structures ...
Aufsatz
Effect of Grain Statistics on Micromechanical Modeling: The Example of Additively Manufactured Materials Examined by Electron Backscatter Diffraction
(2020-02-21)
Micromechanical modeling is one of the prominent numerical tools for the prediction of mechanical properties and the understanding of deformation mechanisms of metals. As input parameters, it uses data obtained from microstructure characterization techniques, among which the electron backscatter diffraction (EBSD) technique allows us to understand the nature of microstructural features, that are usually described by statistics. Because of these advantages, the EBSD dataset is widely used for synthetic microstructure ...
Aufsatz
Predicting Flow Stress Behavior of an AA7075 Alloy Using Machine Learning Methods
(2022-09-09)
The present work focuses on the prediction of the hot deformation behavior of thermo-mechanically processed precipitation hardenable aluminum alloy AA7075. The data considered focus on a novel hot forming process at different tool temperatures ranging from 24°C to 350°C to set different cooling rates after solution heat-treatment. Isothermal uniaxial tensile tests in the temperature range of 200°C to 400°C and at strain rates ranging from 0.001 s-¹ to 0.1 s-¹ were carried out on four different material conditions. ...