Suche
Anzeige der Dokumente 101-110 von 143
Aufsatz
Comparative environmental footprint analysis of ultra-high-performance concrete using Portland cement and alkali-activated materials
(2023-05-22)
Considering the ambitious greenhouse gas emission reduction and efficient use of resource targets set by the Sustainable Development Goals and the importance of concrete structures to achieve these goals, there is an increasing need to study the environmental performance of different concrete production alternatives. Cement is one of the main building materials that contribute significantly to global warming; therefore, studying the environmental performance of innovative binders that can substitute the use of cement ...
Aufsatz
Effect of Auger recombination and leakage on the droop in InGaN/GaN quantum well LEDs
(Optical Society of America, 2014)
We investigate the effect of the epitaxial structure and the acceptor doping profile on the efficiency droop in InGaN/GaN LEDs by the physics based simulation of experimental internal quantum efficiency (IQE) characteristics. The device geometry is an integral part of our simulation approach. We demonstrate that even for single quantum well LEDs the droop depends critically on the acceptor doping profile. The Auger recombination was found to increase stronger than with the third power of the carrier density and has ...
Aufsatz
Lifetime Prediction with Combined Hygro-Thermo-Mechanical Influences on Thick Layer Adhesives
(2023-05-31)
Semi-structural bonded joints of steel components are exposed to long-term stresses in addition to water diffusion, temperature changes and varying external forces during operation. These hygro-thermomechanical loadings lead to successive degradation of stiffness and strength due to damage resulting from chemical aging and fatigue processes, causing failure of the bonded joint when its service life is reached. In the following contribution, a methodology is presented to predict the service life of hygro-thermo-mechanically ...
Aufsatz
Optimal attitude maneuvers in the presence of prohibited directions
(2023-05-31)
We consider the problem of realigning a space telescope from one observation target to the next in the presence of prohibited directions. More specifically, we want to steer the space telescope – modelled as a gyrostat – from an initial attitude at rest to a final attitude at rest within a fixed time interval. During the motion, the line of sight of the telescope must be kept away from forbidden directions towards bright objects like the sun, moon or earth due to power or thermal requirements. The kinematics of the ...
Aufsatz
Influence of Mean Stress on Lifetime Prediction of Adhesive Bonds
(2023-05-31)
The importance of adhesive bonds in the field of joining technology is increasing due to their advantageous properties. One of these attributes is the possibility to reduce the weight compared to welded joints in group of components. For a safe design, the knowledge of the lifetime of these components is essential. Various methods are used for the prediction of the lifetime under cyclic loading. On the one hand there are test-based methods, on the other hand simulation-based approaches. Test-based ones are often ...
Aufsatz
A novel cubic-exp evaluation algorithm considering non-symmetrical axial response signals of confocal microscopes
(2023-06-26)
The depth discrimination in confocal microscopy is based on the digital analysis of depth response signals obtained by each camera pixel during measurement. Various signal-processing algorithms are used for this purpose. The accuracy of these algorithms is inter alia restricted by the axial symmetry of the signals. However, in practice response signals are rather asymmetrical especially in case of measurement objects with critical surface structures such as edges or steep flanks. We present a novel signal-processing ...
Aufsatz
Vibrationally Resolved Absorption and Fluorescence Cross Sections of Adamantane in the Far-ultraviolet Spectral Range on an Absolute Scale
(2023-07-20)
High-resolution absorption, dispersed fluorescence emission, and photoionization cross sections are presented for gas-phase adamantane excited by synchrotron radiation in the exciting-photon energy range of 6–30 eV. Relative and absolute absorption cross sections of so-far unmatched resolution of down to 0.27 cm−¹ line width in the region from 6.4–28 eV are shown along with newly discovered vibronic substructures around the HOMO–LUMO transition. Absorption line positions are provided with very high accuracy and listed ...
Aufsatz
Hybrid modeling of viscoelastic and switching–induced heating in ferroelectrics
(2023-03-24)
This contribution focuses on two effects causing a temperature change in electrically loaded ferroelectrics. These materials are often subjected to cyclic loading, where viscoelasticity prevails at lower electric fields, whereas dissipative heating by domain switching dominates above the coercive field. While viscoelasticity is modeled within a phenomenological, rheological framework, the ferroelectric constitutive behaviour is described based on a microphysical model. Merging both approaches results in the hybrid ...
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...