Search
Now showing items 41-50 of 93
Konferenzveröffentlichung
Unsymmetrische Beiträge zur Momentanreserve durch Erzeugung, Verbrauch und Speicher
(Conexio-PSE GmbH, 2022)
Im Zuge der Dekarbonisierung müssen Verbundsysteme auf wiederkehrende Situationen vorbereitet werden, während derer sie vor allem aus Wechselrichtern gespeist werden. Der stabilisierende Einfluss der durch Synchrongeneratoren direkt an das Netz gekoppelten Schwungmassen auf jede Frequenzveränderung ist heute unverzichtbar. Die inhärente Sofortreaktion von Synchronmaschinen auf Spannungswinkeländerungen und Frequenzbewegungen heißt Momentanreserve. Wenn sich Verbrauch oder Erzeugung dynamisch ändern, und besonders ...
Konferenzveröffentlichung
Assessment of the changeability of plastics processing systems
(Society of Plastics Engineers, 2014)
Changeable production systems are still being developed, especially in the field of plastics processing. Here, the assessment of the changeability is a decisive factor. This investigation deals with the assessment of the changeability of a modular pilot plant, and derives approaches for the further development of an evaluation system, as well as potential means to increase the changeability.
Konferenzveröffentlichung
The Adhesion of LSR Thermoplastic Composites after Storage Tests
(Society of Plastics Engineers, 2017)
The adhesion properties of liquid silicone rubber (LSR) and different thermoplastics (PC, PA, and PP) were examined in this investigation. In order to guarantee the adhesion of both components, an activation (silicatization) of the TP surface, which is a conventional method, was carried out. Furthermore, the long-term stability of the silicatization (storage of the activated surfaces) as well as the wetting behavior were investigated. Moreover, microscopic investigations were performed to analyze the activated ...
Konferenzveröffentlichung
Flexible Foams made of Liquid Silicone Rubber and expandable Microspheres
(2019-10-02)
In this study, the possibility of foaming liquid silicone rubber (LSR) was investigated. The foam was produced by injection molding with two different thermoplastic, expandable microspheres. Different properties were tested using the S2-tensile bar, e.g. density, tensile strength, specific tensile strength, elongation at break, stress at 100 % strain and the hardness. It was found that the two types of microspheres used have similar effects on density, specific tensile strength and elongation at break, but differ in ...
Konferenzveröffentlichung
The lexicalization of complex constructions: an analysis of adjective-noun combinations
(Pasithee : Open Access Electronic Publications; Library & Information Center - University of Patras, 2016)
The current paper discusses the lexicalization of complex constructions composed of an adjective and a noun. It is argued that compounds/compound-like constructions are more prone to become lexicalized than phrases/phrase-like constructions. The relationship between lexicalization and the cognitive process of memorization represents a key point of our analysis. We report evidence from psycholinguistic studies contrasting compounds/compound-like constructions to phrases/phrase-like constructions either within a single ...
Konferenzveröffentlichung
Designing a Conversational Agent as a Formative Course Evaluation Tool
(GITO Verlag, 2020)
Today’s graduating students face ever-changing environments when they enter their job life. Educational institutions must therefore continuously develop their course structure and content in order to prepare their students to be future employees. A very important means for developing the courses is the students’ course evaluations. Due to financial and organizational restrictions, these course evaluations are usually carried out quantitatively and at the end of the semester. However, past research has shown that this ...
Konferenzveröffentlichung
The Influence of different die geometries on the Extrusion Process of High-Consistency Silicone Rubber
(Society of Plastics Engineers, 2019)
Silicone Rubber and especially High-Consistency Silicone Rubber (=HCR), are typically processed in the extrusion process. Due to the high requirements in terms of the ma-terial properties and the geometric dimensions, a funda-mental knowledge of the whole process including experi-ences in tool design are essential.
In this study, HCR with different Shore-hardnesses are extruded on a vertical silicone extrusion line with various breaker plates with different length to diameter ratios (=L/D-ratio) in order to analyze ...
Konferenzveröffentlichung
Pull and Foam - Injection moulding method: Foamed ribs for stiffening plane components
(Society of Plastics Engineers, 2012)
The pull and foam method is a foam injection moulding method which is currently being developed at the Institut für Werkstofftechnik (IfW) (Institute of Materials Engineering) at the University of Kassel. The processing principle represents an alternative to the existing foam injection moulding special procedures and introduces the possibility to partially foam a component. In so doing, thin-walled, hardly foamed components with foamed ribs can be made in one processing step, thus also components with graded ...
Konferenzveröffentlichung
The Effect of Injection Molding Parameters on Microcellular Foam Morphology
(2021)
Microcellular foam injection molding with physical blowing agent (MuCell®) delivers monetary benefits, processing advantages and freedom of product design by reducing shrinkage. In conjunction with an advanced mold technology, so-called Pull and Foam method, there is great potential in controlling the foam structure of the component locally. In this study, Polycarbonate (PC) components were produced with nearly compact outer skin and a closed cellular core. To understand the relation between processing parameters and ...
Konferenzveröffentlichung
Formation of morphology as a function of process control by foam injection molding of a functionally graded component
(Society of Plastics Engineers, 2014)
A special mold technology enables the production of foam injection molded components with locally differing foaming ratios. Thus, components with functionally graded foam structures can be produced in one processing step. The method (pull and foam method) is based on the idea of creating components with thin-walled areas with a high surface quality and partially foamed, thick-walled areas (e.g. with the function of integrated structural elements) in a controlled foaming process. This paper describes the characteristics ...