Suche
Anzeige der Dokumente 81-87 von 87
Aufsatz
Effect of Compositional Variation Induced by EBM Processing on Deformation Behavior and Phase Stability of Austenitic Cr-Mn-Ni TRIP Steel
(2020-01-24)
Electron beam melting (EBM) is an established powder bed-based additive manufacturing process for the fabrication of complex-shaped metallic components. For metastable austenitic Cr-Mn-Ni TRIP steel, the formation of a homogeneous fine-grained microstructure and outstanding damage tolerance have been reported. However, depending on the process parameters, a certain fraction of Mn evaporates. This can have a significant impact on deformation mechanisms as well as kinetics, as was previously shown for as-cast material. ...
Aufsatz
On the Impact of Texture and Grain Size on the Pseudoelastic Properties of Polycrystalline Fe–Ni–Co–Al–Ti Alloy
(2020-05-08)
The effects of thermomechanical treatments on crystallographic texture and grain size evolution and their impact on the pseudoelastic properties in Fe41–Ni28–Co17–Al11.5–Ti2.5 (at.%) were studied in the present paper. The results show that cold rolling leads to brass-type texture in this alloy, which is typical for low stacking fault energy materials. Thermal treatments up to 1300 °C were conducted and it is shown that the presence of β-phase helps to control grain growth. After the dissolution of the secondary phase ...
Aufsatz
On the Influence of Surface Hardening Treatments on Microstructure Evolution and Residual Stress in Microalloyed Medium Carbon Steel
(2020-06-09)
Tailoring surface properties is a key to superior performance of components subjected to fatigue loadings in application. Process–microstructure–property relationships have to be established to allow for optimization of techniques employed for surface treatments such as deep rolling and induction hardening. Although both techniques are employed widely in industrial application, studies examining microstructure evolution and residual stress states for a single material in a comparative manner are missing. Amongst ...
Aufsatz
On the Influence of Microstructure on the Corrosion Behavior of Fe–Mn–Al–Ni Shape Memory Alloy in 5.0 wt% NaCl Solution
(2020-10-03)
Herein the corrosion behavior of Fe–Mn–Al–Ni shape memory alloys characterized by different microstructures in a 5.0 wt% NaCl solution is investigated. Open circuit potential and potentiodynamic polarisation tests are conducted. Generally, Fe–Mn–Al–Ni shows corrosion properties being similar to pure iron. However, the polarization curves of single crystals indicate the presence of an unstable passive system. The corrosion damage is analyzed by means of optical microscopy and electron microscopy. It is revealed that ...
Aufsatz
Investigation of residual stresses in polypropylene using hot plate welding
(2020-08-05)
During the cooling process of the molten material, residual stresses appear because the reduced volume of the cooled material cannot fully fill the space formerly occupied by the molten material. The morphology in and around the weld is formed by different factors depending on the material and process parameters. Different morphological structures relate to different mechanical properties. The process parameters and the welding results including morphology and residual stress are linked together. In this article, ...
Aufsatz
Ordoliberalism Out of Order? The Fragile Constitutionality of Greek Austerity (Part Two)
(2020-06)
This is the second part of a two-part post. The first part, available here, considered the historical background of the concept of constitutional order and its relation to the ordoliberal project. Judicial independence was examined in parallel with central bank independence, with each understood as a means of insulating policy from social and democratic pressures and also as a means of enacting and maintaining fiscal discipline and market-conforming order. It also included some preliminary observations on the relation ...
Aufsatz
Joining of Contact Pins and Conductive Compounds via Injection Molding – Influence of the Flow Situation on the Electrical Contact Resistance
(2020-04-09)
While a lot of research can be found in the field of bulk resistance of carbon filled polymers, comparatively few papers focus on contact resistance between compound and metal contacts. Due to that small number of researches that deal with contact resistances, studies of the influence of injection molding conditions and parameters on the contact resistance are also very rare. In contradiction to that, these influences on bulk resistance have been studied. The objective of this work was to investigate the electrical ...